mr/openwrt
2
0
Fork 1
Code Issues 7 Pull Requests Releases Wiki Activity
19,210 Commits 3 Branches 0 Tags 517 MiB
0baa69ddda
Commit Graph

198 Commits

Author SHA1 Message Date
Gabor Juhos
3a7b12a27d ar71xx/all0258n: sysupgrade support 
U-Boot on the ALL0258N needs offset, size and md5 for kernel and rootfs to be
stored in the U-Boot environment.
If the checksums don't match during boot, a failsafe-system is booted instead.
This patch adds a board-specific sysupgrade hack for the all0258n which
calculates and updates the checksums for the U-Boot environment.

Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 28700
 2011-11-01 09:23:32 +00:00
Gabor Juhos
f40557a692 ar71xx/all0258n: add default config 
This adds default network and uboot-env settings for the ALL0258N.

Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 28699
 2011-11-01 09:23:31 +00:00
Gabor Juhos
06d9653b36 ar71xx: remove default network config of the mzk-w04nu board as well 
It works with the generic config.

SVN-Revision: 28695
 2011-11-01 09:23:25 +00:00
Gabor Juhos
693c777eaf ar71xx: remove LED setup of nonexistent interfaces on RB750 
SVN-Revision: 28693
 2011-10-31 14:26:56 +00:00
Gabor Juhos
2bcd612e72 ar71xx: remove default network config of the wnr2000 board 
It is the same as the generic configuration.

SVN-Revision: 28692
 2011-10-31 14:26:51 +00:00
Gabor Juhos
39b3bfcf6a ar71xx/sysupgrade: use $magic_long instead of $magic when comparing with a 32-bit value 
Aparently $magic_long was meant here instead of $magic when comparing with
32-bit values.

Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 28678
 2011-10-30 13:06:30 +00:00
Gabor Juhos
1646346798 ar71xx: add initial support for the OpenMesh OM2P board 
Based on a patch by Marek Lindner <marek@open-mesh.com>

SVN-Revision: 28617
 2011-10-27 07:54:51 +00:00
Gabor Juhos
9d51cda2db ar71xx: Buffalo WHR-HP-G300N kernel support 
The initial support for the Buffalo WHR-HP-G300N box.
The code was confirmed to boot and run, but not tested in depth.

Known problem: iw phy phy0 info shows:
	Coverage class: 0 (up to 0m)
	Available Antennas: TX 0 RX 0

Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>

SVN-Revision: 28567
 2011-10-24 21:49:26 +00:00
Gabor Juhos
d96e321bd1 ar71xx: add kernel support for the Allnet ALL0258N board 
This patchs adds support for the Allnet ALL0258N outdoor AP/bridge.
The ALL0258N is based on the AR7240 SoC paired with an AR9285 radio,
it got 8MB of NOR and 32MB SDRAM.

Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 28564
 2011-10-24 21:49:21 +00:00
Jo-Philipp Wich
b61de9c865 base-files: make sure inittab-console-fixup returns with success (#10275) 
SVN-Revision: 28562
 2011-10-24 21:35:43 +00:00
Jonas Gorski
a136b67604 linux: ar71xx: add support for Mikrotik Routerboard RB493G 
SVN-Revision: 28423
 2011-10-11 23:05:16 +00:00
Gabor Juhos
e45d7d7006 ar71xx: enable login only on the system console by default 
SVN-Revision: 28294
 2011-09-23 19:56:38 +00:00
Gabor Juhos
733399600f ar71xx: add support for the TP-Link TL-WR703N v1 board 
Based on a patch by dongyuqi <729650915@qq.com>

SVN-Revision: 28277
 2011-09-21 11:47:53 +00:00
Gabor Juhos
85b858fae6 ar71xx: enable sysupgrade on the AP96 and DB120 boards 
SVN-Revision: 27901
 2011-08-04 19:41:18 +00:00
Gabor Juhos
fb77134596 ar71xx: use the same test for AP121 and Zcomax sysupgrade images 
SVN-Revision: 27900
 2011-08-04 19:41:17 +00:00
Jonas Gorski
e18ceb1dac ar71xx: merge WZR-HP-G301NH support into WZR-HP-G300NH 
Now that we can use a generic name for the switch there is no need for a
separate image for the WZR-HP-G301NH.
Update the default network config and remove the extra image.

SVN-Revision: 27814
 2011-07-28 11:57:51 +00:00
Felix Fietkau
7afed2d86c ar71xx: add wzr-hp-ag300h sysupgrade support (patch from #9650) 
SVN-Revision: 27434
 2011-07-04 03:03:34 +00:00
Jo-Philipp Wich
701543d3ef revert r27043 (#9513) 
SVN-Revision: 27343
 2011-07-01 19:52:57 +00:00
Jo-Philipp Wich
1edef5ec98 revert r27341, it introduce wrong behaviour for other models 
SVN-Revision: 27342
 2011-07-01 19:15:45 +00:00
Jo-Philipp Wich
3b3103b2f1 turn status LED off if device finished initializing 
SVN-Revision: 27341
 2011-07-01 18:39:53 +00:00
Felix Fietkau
cc56af716c ar71xx: add default network config for wzr-hp-ag300h (based on a patch from #9607) 
SVN-Revision: 27283
 2011-06-25 13:54:42 +00:00
Vasilis Tsiligiannis
70106f153d Remove trailing spaces, convert spaces to tabs 
SVN-Revision: 27153
 2011-06-09 19:30:50 +00:00
Felix Fietkau
9160e06af5 ar71xx: override inittab to enable login on ttyATH0 
SVN-Revision: 27128
 2011-06-07 17:07:10 +00:00
Gabor Juhos
9e435c03e0 ar71xx: add sysupgrade support for the AP121 boards 
SVN-Revision: 27069
 2011-05-31 22:53:45 +00:00
Gabor Juhos
646937135f ar71xx: add default network config for the AP121 boards 
SVN-Revision: 27068
 2011-05-31 22:53:44 +00:00
Gabor Juhos
650c7cc2fd ar71xx: use the diag LED for diagnostic on the WZR-HP-G30XNH boards 
SVN-Revision: 27043
 2011-05-31 22:53:13 +00:00
Gabor Juhos
4834fdaccd ar71xx: fix uci-defaults script for the WZR-HP-G30XNH boards 
SVN-Revision: 27042
 2011-05-31 22:53:12 +00:00
Gabor Juhos
b39eebdf1e ar71xx: add uci config for the WLAN LED on the WRT160NL 
Based on a patch by Magyar Szabolcs <mszabi@freemail.hu>

SVN-Revision: 26861
 2011-05-08 21:38:49 +00:00
Gabor Juhos
858e2e719b ar71xx: use phy0tpt trigger for the WLAN LEDs 
SVN-Revision: 26860
 2011-05-08 21:38:48 +00:00
Felix Fietkau
cbc75a9c70 ar71xx: use the ar8316 switch driver on the PB92 board and add a matching default network config 
SVN-Revision: 26779
 2011-04-28 21:27:42 +00:00
Alexandros C. Couloumbis
f13581eedb linux/ar71xx: update wget2nand script 
SVN-Revision: 26747
 2011-04-21 12:38:25 +00:00
Gabor Juhos
e193547733 ar71xx: use the gpio_keys_polled driver instead of gpio_buttons 
SVN-Revision: 26603
 2011-04-12 09:29:21 +00:00
Gabor Juhos
54ede24829 ar71xx: Add support for WZR-HP-G301NH 
Add support for the Buffalo WZR-HP-G301NH. The only difference between it
and the WZR-HP-G00NH is that it has a RTL8366RB instead of a RTL8366S.
Since we don't do runtime detection of the switch, we need a separate
machine definition for it.

While we are at it, also rename the profile to reflect that it now is for
more than one device.

Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>

SVN-Revision: 26601
 2011-04-12 09:29:10 +00:00
Felix Fietkau
784d808d07 ar71xx: add default configuration for the switch on AP96 
Enables forwarding of frames between the switch ports (eth0).
Patch by Jouni Malinen

SVN-Revision: 26180
 2011-03-15 19:51:42 +00:00
Gabor Juhos
8eb616de82 ar71xx: add support for the TP-Link TL-WA901ND v2 board 
Patch-by: Jonathan Benett <jbscience87@gmail.com>

SVN-Revision: 26119
 2011-03-13 15:08:31 +00:00
Gabor Juhos
67c3e0bf7e ar71xx: add support for the WNDR3700v2 board 
Based on a patch by Mark Mentovai <mark@moxienet.com>

SVN-Revision: 25118
 2011-01-26 20:35:42 +00:00
Gabor Juhos
061228d73c ar71xx: make uci-default scripts executable 
Reported-by: Nuno Gonçalves <nunojpg@gmail.com>

SVN-Revision: 24897
 2011-01-04 13:44:01 +00:00
Claudio Mignanti
2c0596cd69 unifi: add sysupgrade and leds support 
SVN-Revision: 24737
 2010-12-20 17:28:34 +00:00
Gabor Juhos
e7ea6387a3 ar71xx: use usbdev trigger for USB LEDs by default 
SVN-Revision: 24648
 2010-12-17 17:10:16 +00:00
Gabor Juhos
a26c3e60e2 ar71xx: populate LED configuration for WZR-HP-G300NH 
Signed-off-by: Dave Lichterman <laviddichterman@gmail.com>

[nand-disk trigger has been removed - juhosg]

SVN-Revision: 24642
 2010-12-17 17:09:57 +00:00
Gabor Juhos
a2a5598c00 ar71xx: add wlan led for the TL-WR941ND 
SVN-Revision: 24612
 2010-12-15 19:55:50 +00:00
Gabor Juhos
9f38f9bf76 ar71xx: add missing files for the JA76PF board 
SVN-Revision: 24444
 2010-12-10 19:55:28 +00:00
Gabor Juhos
b680f088ba ar71xx: add support for the jjPlus JA79PF 
Patch-by: Cezary Jackiewicz

SVN-Revision: 24440
 2010-12-10 17:57:51 +00:00
Gabor Juhos
5b0c83edd9 ar71xx: add support for the TP-LINK TL-MR3220 v1 board 
SVN-Revision: 24439
 2010-12-10 17:57:48 +00:00
Gabor Juhos
83834da33b ar71xx: add default network configuration file for the TL-MR3420 
SVN-Revision: 24437
 2010-12-10 17:57:40 +00:00
Gabor Juhos
081796fe47 ar71xx: add nbg460n image generation 
This adds image generation for NBG460N/550N/550NH boards.

Signed-off-by: Michael Kurz <michi.kurz@googlemail.com>

SVN-Revision: 24419
 2010-12-10 15:17:03 +00:00
Jo-Philipp Wich
6f7e2d4ce8 tune rtl8366s default config, make vlan 1 cpu port tagged and use eth0.1 for the lan interface - this brings the configuration more in line with other switch setups 
SVN-Revision: 24215
 2010-12-02 20:19:55 +00:00
Felix Fietkau
5f3f1b8cd8 ar71xx: Configure WNDR3700 switch LED colors properly (#8103) 
For WNDR3700, use green for 1Gb/s and amber for 100Mb/s and 10Mb/s on
the four LAN port switch LEDs. The LEDs will be lit to indicate a link
and will blink to indicate activity. This matches the stock firmware
and the description printed on the label on the unit's underside.

Signed-off-by: Mark Mentovai <mark@moxienet.com>

SVN-Revision: 23879
 2010-11-04 18:55:16 +00:00
Felix Fietkau
b3b2227869 Revert "ar71xx: WNDR3700 WiFi LEDs should blink for activity (#7984)" on submitter's request 
SVN-Revision: 23878
 2010-11-04 18:53:18 +00:00
Felix Fietkau
77eee74d56 ar71xx: WNDR3700 WiFi LEDs should blink for activity (#7984) 
Make the WiFi LEDs blink for activity on the WNDR3700, matching the
stock firmware and user expectations. The green 2.4GHz and blue 5GHz
LEDs will illuminate with the radio on, and will blink to indicate
transmission and reception.

Signed-off-by: Mark Mentovai <mark@moxienet.com>

SVN-Revision: 23877
 2010-11-04 18:48:22 +00:00
Felix Fietkau
fc035b3cb6 ar71xx: remove dev-ap91-eth.c. switch its only user (RB-750) to the new switch driver 
SVN-Revision: 23439
 2010-10-14 13:41:42 +00:00
Felix Fietkau
3941621dbc ar71xx: use the new ar7240 switch driver on the DIR-600-A1 as well (fixes #7563) 
SVN-Revision: 23432
 2010-10-14 00:14:59 +00:00
Gabor Juhos
697f5d0bdd ar71xx: initial support for jjPlus JWAP003 
Patch-by: Cezary Jackiewicz <cezary@eko.one.pl>

(the GPIODEV code has been removed, the sysfs interface
can be used to control the GPIO lines instead - juhosg)

SVN-Revision: 23165
 2010-10-01 07:09:29 +00:00
Gabor Juhos
32d12d5e5c ar71xx: add support for the TL-MR3420 v1 board 
SVN-Revision: 23136
 2010-09-27 14:53:59 +00:00
Felix Fietkau
a7bb7dd99e Add support for Atheros AP96 reference board 
This is still preliminary and not really tested much. Anyway, this
version seems to be enough to get both wired and wireless
interfaces working. Buttons and leds are also working.

mach-ap96.c is based on mach-wndr3700.c.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>

SVN-Revision: 23125
 2010-09-27 08:59:53 +00:00
Gabor Juhos
b4336a8e2d ar71xx: add support for the Zcomax ZCN-1523H-2-8/5-16 boards 
SVN-Revision: 22882
 2010-09-03 18:14:37 +00:00
Felix Fietkau
523fcf0497 ar71xx: add a new driver for the ar7240 switch using swconfig. hooks directly into the ethernet driver, as MAC resets also require switch reinitializations and the switch is part of the cpu core anyway switch only tl-wr741nd (and other devices using this board file, such as tl-wr841nd) over to using this by default, as other devices are still untested fixes #7563 
SVN-Revision: 22675
 2010-08-16 19:21:57 +00:00
Gabor Juhos
e35f7ef51d ar71xx: add eap7660d board to diag.sh and sysupgrade 
This patch adds support for the Senao EAP7660D board to diag.sh and sysupgrade.

Signed-off-by: Daniel Golle <daniel.golle@gmail.com>

SVN-Revision: 22644
 2010-08-14 21:07:31 +00:00
Alexandros C. Couloumbis
9aef272f4a linux/ar71xx: add nanostation-m signature (thanks Antonio Anselmi) 
SVN-Revision: 22631
 2010-08-14 07:48:05 +00:00
Jo-Philipp Wich
6616951c15 add uci-defaults script to migrate vlan 0 to vlan 1 after sysupgrade on devices using the RTL8366s switch 
SVN-Revision: 22625
 2010-08-13 19:29:51 +00:00
Felix Fietkau
4ee3ae96c2 ar71xx: fix sysupgrade on the ubnt nanostation m 
SVN-Revision: 22370
 2010-07-23 18:16:47 +00:00
Felix Fietkau
900aaa919b ar71xx: add support for the tp-link tl-wa901nd devices (patch by Pieter "Fate" Hollants, from #7528, without the ethernet fifo cfg values) 
SVN-Revision: 22353
 2010-07-22 12:37:44 +00:00
Jo-Philipp Wich
d6d8014cfd fix dir-825-b1 default network config after r21905 
SVN-Revision: 22005
 2010-07-01 00:03:43 +00:00
Gabor Juhos
e827a12c48 ar71xx: don't use vlan 0 for devices with rtl8366s switch 
SVN-Revision: 21905
 2010-06-26 19:15:32 +00:00
Gabor Juhos
7bff9c0101 ar71xx: add support for the Senao EAP7660D board 
This patch adds support for the Senao EAP7660D board to trunk.

Signed-off-by: Daniel Golle <daniel.golle@gmail.com>

SVN-Revision: 21837
 2010-06-18 16:22:05 +00:00
Gabor Juhos
518f43efd8 ar71xx: fix RB750 LED configuration 
Patch-by: Ray Bellis

SVN-Revision: 21826
 2010-06-17 09:24:26 +00:00
Gabor Juhos
b86e4e1c6a ar71xx: add default network config for the RB433UAH board 
SVN-Revision: 21765
 2010-06-12 13:20:41 +00:00
Gabor Juhos
3045632eb0 ar71xx: add default network configuration file for the RB450/RB433 boards 
SVN-Revision: 21730
 2010-06-08 20:19:23 +00:00
Daniel Dickinson
6bccc41f6c ar71xx: Added preinit scriptlet to set vars based on cpuinfo during preinit_main. This fixes a bug in which the vars were not set due to /proc not being mounted when ar71xx.sh was sourced 
SVN-Revision: 21634
 2010-05-30 03:20:49 +00:00
Gabor Juhos
65dba323f7 ar71xx: Make wget2nand fail if copying the kernel fails and use the correct file extension for the rootfs image 
wget2nand didnt check the exit status after copying the kernel, if the
copying failed for some reason ( for example not enougs space on the
kernel partition) it simply continued extracting the rootfs.
I also changed the filename, which wget2nand trys to download (
.tar.gz instead of .tgz ).

Signed-off-by: Marko Foerster <mrkfoerster@googlemail.com>

SVN-Revision: 21444
 2010-05-14 08:38:39 +00:00
Gabor Juhos
d6c0363884 ar71xx: make the AR8216 driver usable on the TEW-632BRP/DIR-615-Cx boards 
Cc: backfire@openwrt.org

SVN-Revision: 20752
 2010-04-09 08:40:09 +00:00
Jo-Philipp Wich
23bebe33a7 Add support for the ar8316 switch. This patch enhances the ar8216 driver with ar8316 support and fixes some minor issues with the ar8216 driver itself. It should not break anything, but isn't tested on ar8216 devices. 
[PATCH 2/2] ar71xx: Add the ar8316 driver to rs pro/rb-450g.
Add the ar8216 driver to the ar71xx target, and add network
configurations for the RouterStation Pro and the RouterBoard RB-450G.

SVN-Revision: 20722
 2010-04-05 23:03:16 +00:00
Gabor Juhos
8701291f0f ar71xx: add uci defaults to fix trx header on the WRT160NL boards 
* patch by Otto Solares

SVN-Revision: 20526
 2010-03-27 17:38:40 +00:00
Gabor Juhos
35bb7be34d ar71xx: Add basic WLAN LED control to TL-WR1043ND 
* thanks to KillaB
  * closes #6834

SVN-Revision: 20415
 2010-03-25 07:31:17 +00:00
Gabor Juhos
0095ab73f3 ar71xx: fix defconfig script to work with ImageBuilder 
* patch from #5722

SVN-Revision: 20231
 2010-03-15 13:29:16 +00:00
Gabor Juhos
ed3aca86a6 ar71xx: don't break the existing network configuration in the wget2nand script 
SVN-Revision: 20228
 2010-03-15 11:03:33 +00:00
Gabor Juhos
9daf566ddc ar71xx: fix sysupgrade on the LS-SR71 board 
SVN-Revision: 20119
 2010-03-10 17:41:45 +00:00
Gabor Juhos
eaccbd3fb8 ar71xx: add default network configuration for the PB44 board 
SVN-Revision: 20099
 2010-03-09 18:05:58 +00:00
Gabor Juhos
18ee1b6dda ar71xx: add uci-defaults for the RB750 board 
SVN-Revision: 20097
 2010-03-09 18:05:51 +00:00
Gabor Juhos
b21308313e ar71xx: override lan port names on the RB750 
SVN-Revision: 20096
 2010-03-09 18:05:48 +00:00
Gabor Juhos
781c482e6a ar71xx: improve wget2nand script 
SVN-Revision: 20094
 2010-03-09 18:05:42 +00:00
Gabor Juhos
4d5a9fe402 ar71xx: add missing protocol definitions to default network configurations 
SVN-Revision: 20091
 2010-03-09 18:05:31 +00:00
Gabor Juhos
5e8c8818ed ar71xx: add preliminary support for the RouterBOARD 750 
SVN-Revision: 20029
 2010-03-07 05:41:01 +00:00
Gabor Juhos
52f03512dc ar71xx: fix sysupgrade on the WRT400N (thanks to chuljin) 
* closes #6782

SVN-Revision: 20006
 2010-03-05 20:29:27 +00:00
Gabor Juhos
7bda582cf7 ar71xx: fix status led detection on the RB4xx boards 
SVN-Revision: 20005
 2010-03-05 20:29:24 +00:00
Gabor Juhos
e1bb4af48b ar71xx: add default network configuration file for the TL-WR741ND board 
SVN-Revision: 19930
 2010-03-01 07:34:48 +00:00
Gabor Juhos
3f7d3dc939 ar71xx: add default network configuration file for the DIR-600 rev. A1 board 
SVN-Revision: 19929
 2010-03-01 07:34:46 +00:00
Gabor Juhos
a6be62a4f1 ar71xx: add default network configuration file for the TL-WR1043ND board 
Thanks to Andrew Tarabaras.

SVN-Revision: 19840
 2010-02-24 13:39:20 +00:00
Gabor Juhos
187d5546db ar71xx: use the correct name for the status LED on the WRT400 board (thanks to chuljin, patch from #6734) 
SVN-Revision: 19831
 2010-02-24 13:38:37 +00:00
Gabor Juhos
560f7173b2 ar71xx: update default network configuration file for the WNDR3700 
Signed-off-by: Scott Dudley <spmsink@hotmail.com>

SVN-Revision: 19830
 2010-02-24 13:38:31 +00:00
Gabor Juhos
47990f61fb ar71xx: add uci configuration for the WAN LED on the WNDR3700 
Based on a patch by Scott Dudley <spmsink@hotmail.com>

SVN-Revision: 19746
 2010-02-19 11:52:25 +00:00
Felix Fietkau
0e84ed29ea preinit: fix mixup between led and reset button enable on some platforms (thx, cshore) 
SVN-Revision: 19370
 2010-01-28 19:28:02 +00:00
Felix Fietkau
56bc02a305 add preinit modularization work by Daniel Dickinson (cshore) 
SVN-Revision: 19331
 2010-01-25 17:11:17 +00:00
Gabor Juhos
2b5ba9073f rtl8366_smi: move RTL8366S driver into a separate file 
SVN-Revision: 19279
 2010-01-22 17:38:07 +00:00
Gabor Juhos
b9328f2e04 ar71xx: change failsafe message 
SVN-Revision: 19221
 2010-01-18 09:15:35 +00:00
Gabor Juhos
a9c5e3159f ar71xx: update default network configuration for the WNDR3700/DIR-825-B1 
Also drop the default network configuration of the TL-WR1043ND, because
the RTL8366RB switch is not yet supported by the rtl8366-smi driver.

SVN-Revision: 19217
 2010-01-18 09:01:47 +00:00
Felix Fietkau
a86a28841c ar71xx: add some default configs for rtl8366 based devices 
SVN-Revision: 19210
 2010-01-18 00:44:52 +00:00
Felix Fietkau
3cc98b09f7 adjust switch default configs for the swconfig api change 
SVN-Revision: 19209
 2010-01-18 00:38:08 +00:00
Gabor Juhos
21a235bc67 ar71xx: fix typos in the ar71xx.sh 
SVN-Revision: 19151
 2010-01-15 12:11:05 +00:00
Gabor Juhos
cb80426641 ar71xx: add preliminary support for the Buffalo WZR-HP-G300NH 
SVN-Revision: 19150
 2010-01-15 12:08:03 +00:00