This patch also makes use of the new leds script.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41585
This adds support for Comtrend WAP-5813n.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: refresh patches]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41421
Support for Asmax AR 1004g router
Signed-off-by: Adrian Feliks <mexit@o2.pl>
Patchwork: http://patchwork.openwrt.org/patch/4464/
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39674
This adds profile and build image for Sagemcom F@st2704, using b43
driver.
For WiFi to work properly BCMA fallback SPROM support patch must
be applied (http://git.io/z1Ki8A).
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4212/
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39673
In order to support both normal images and initramfs, ensure that each
target sets KERNELNAME properly so that the generic kernel building code
can copy the corresponding files over $(KDIR) with the appropriate
extension. Update the various paths to the kernel and wrapper images
from $(LINUX_DIR)/arch/$(ARCH)/boot/$(foo) to $(KDIR)/$(foo).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 37049
Cable Modem devices cannot load an ELF file directly so we need to
provide them with a HCS image even when targetting initramfs.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 36954
$(KDIR)/vmlinux is already a binary image, there is no need to create
another one.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 36949
Signed-off-by: Miguel GAIO <miguel.gaio@efixo.com>
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
[jonas.gorski@gmail.com: add network config for nb6, make switch fix a
platform patch]
SVN-Revision: 32924
Attached patch fixes a typo in the image Makefile, and overrides the
board name for DVA-G3810BN to set the correct board properties
Signed-Off-By: Jeroen van Bemmel <jbemmel@zonnet.nl>
SVN-Revision: 32894
Build images for 96328avng and 963281TAN (untested) for three different
flash sizes: 4MB, 8MB, and 16MB.
Known issues:
* Button setup unknown, thus no fail-safe available.
* All other BCM6328 and BCM63XX issues
SVN-Revision: 32004
Build images for D-Link DSL-274XB revision F1. Flashing
through original web UI as well as CFE works.
Known issues:
* wifi led inverted (on when wifi is off and vice cersa)
* same issues as generic bcm6328 support
SVN-Revision: 31885
Add the required board definition, default config and image generation for
the T-Home Speedport W 303V Typ B.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26878
Rename the DSL-274xB rev C2's board ID to "AW4139" to match the one used
for the rev C3 (same hardware) and add a fixup for C2. Also generate
images for C3.
While we are at it, rename the LEDs to conform to the Linux LED naming
conventions.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26876
Make the fixup board ID independent from the image name to allow using
the same board ID for similar devices.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26874
Add support for the T-Com Speedport W 500V using a special tagged image as it
identifies itself as a 96348GW, but has some gpios wired differently, and also
has only one ethernet port without a switch attached to it.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 24190
