Forgotten patch to fix ethernet for rt2880.
Based on previously submitted patch from Claudio.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 40504
Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg: use zyxel prefix in LED names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40500
With this patch OpenWRT supports the following on the ZyXEL NBG 6716:
-WiFi 2G (ath9k)
-WiFi 5G (ath10k)
-NAND flash
-2 Ethernet interfaces
-USB 2.0
-LEDs including switch
-reasonale defaults at first boot
Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg:
- rename and refresh kernel patch,
- fix a few typos,
- change button key codes,
- use zyxel prefix in LED names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40499
This patch moves ARV7519RW definitions to VR9 section from the AR9 section and removes a whitespace that breaks jffs2 image generation.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 40495
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40481
Apart from the wireless chip, the WNDR3700 v4 and the WNDR4300
is the same device. Indicate this in the kernel files.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40479
The 5V power of the USB is controlled by a GPIO pin of
the external WiFi chip. Setup the GPIO bitmasks in the
platform data of the WiFi chip to ensure that the 5V
power gets enabled by the ath9k driver.
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40478
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40477
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40475
The bootloader does not initializes the output function
correctly for all LEDs. DO that from the board setup code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40474
The hardware manual says amber so change the color part of
the LED names to reflect that. Also update the constant names.
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40473
Adds support for the received signal strength indicator LEDs of the
Bullet M, Nanostation M and Rocket M devices.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/5108/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40471
According to Christophe, the kernel boots on the Soekris net5501
board.
Reported-by: Christophe Prevotaux <cprevotaux@nltinc.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40468
Move the comments out from the shell script to fix build
breakage introduced in r40464.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40466
The C7v2 has 16 MB flash and QCA9880-BR4A rev 2 supported by ath10k driver.
The C7v1 had 8 MB flash and the unsupported QCA9880-AR1A rev 1.
Signed-off-by: Adam Serbinski <adam@serbinski.com>
Patchwork: http://patchwork.openwrt.org/patch/5071/
[juhosg:
- remove the v2 specific profile add the ath10k driver to the existing
Archer C7 profile instead. Although on v1 devices it does not change
the non-working behaviour, but the ath10k driver is useful for users
whom have replaced the wifi card with a supported one in their units.
- update image/Makefile to build firmware image for both boards if the
Archer C7 profile is selected]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40463
* atm module needs to be loaded before linux-atm
* use absolute firmware paths
* extended validation
* add a script for mounting an optional firmware partition
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40460
Place the previous selection (3.3.8) into the only subtarget that did
not override it to 3.10
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40454
This bgmac patch was an attempt to fix/workaround bug reported in
https://dev.openwrt.org/ticket/7198 noticed on WNR3500L.
Patch assumed length reported by the hardware was 0 and was trying to
read it until getting a different value. This was actually the opposite.
Lenghts were some invalid & huge values that resulted in skb_over_panic.
For example:
skbuff: skb_over_panic: text:83b21074 len:57222 (...)
skbuff: skb_over_panic: text:87af1024 len:43226 (...)
skbuff: skb_over_panic: text:87af5024 len:8739 (...)
So instead of that not-working patch checking for 0, write a new one
checking for huge values. In case something like that happens, dump
hardware state and drop the packet.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 40424
this should really be auto detected by the kernel, lets used this workaround until the real
solution is ready
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40418
