This includes:
- use of local 'board' variable in LED names, wherever possible
- merge of boards with exactly the same LED configuration
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Keep everything in alphabetical order. Boards are ordered in two steps,
first within/inside common configuration (case section), then sections,
globally.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This includes:
- code style fixes
- removal of huge comment (it should be in doc, not here) and some small ones
- removal of redundant config for DR531/WPJ531 as the default is the same
- merge of boards with exactly the same interfaces config
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Convert etc/board.d/02_network in ar71xx target to the same shape
as we have in ramips target. Split code into two new functions:
- interface/s setup in ar71xx_setup_interfaces()
- MAC/s setup in ar71xx_setup_macs()
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
sysupgrade command fails due to missing U-Boot environment-processing binaries on sysupgrade ramdisk. The missing binaries result in the following output:
Switching to ramdisk...
Performing system upgrade...
ash: /usr/sbin/fw_printenv: not found
ash: fw_setenv: not found
ash: touch: not found
cannot find target partition
Fixes FS#197.
Signed-off-by: Aaron Curley <accwebs@gmail.com>
- CPU: MT7620A 580MHz
- Flash: 8MB - RAM: 64MB
- External PA+LNA on both WLAN2.4 and WLAN5
- 4x LAN ethernet and 1x WAN ethernet
Signed-off-by: Xuefu Lin <xuefulin@gmail.com>
It missed some changes needed for kernel 4.4. This is only used by the
Falcon SoC and not for the xRX SoCs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The main difference is it supports DT binding. This allows us to use DT
for specifying controller and the new standalone USB 3.0 PHY driver.
Thanks to that we don't need out of tree patch adding PHY initialization
to the controller driver anymore.
This problem has been fixed by upstream commit 757de492f2d ("xhci: fix
platform quirks overwrite regression in 4.7-rc1").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This drops built-in support for USB 2.0 PHY and starts using separated
driver that was upstreamed & backported some time ago.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The nf_reject_* and nf_nat_masquerade_* modules are moved into the
corresponding kmod-nf- packages. Appropriate dependencies are added to the
kmod-nft- packages.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Refresh patches for all targets that support kernel 4.4.
compile/run-tested on brcm2708/bcm2710 only.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Forgot to update kernel-version.mk, so updated patch. Compile-tested on x86/64 and ar71xx; run-tested on x86/64 and ar71xx.
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
-add spi pins
-move mdio and rgmii pinctrl from gmac and mdio into pinmux node
-add i2c4 pinctrl into rpm node
-add pin details into several nodes
-update gmac1 and gmac2 parameters
-update mdio phy0 and phy4 registers by ddwrt devs findings
-fix i2c4 pin drive-strengh
-remove pcie pins as it's already present in ipq8065 DT
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Now that the firmware for BCM43430 has been submitted to linux-firmware use it
and remove RPiDistro package.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add patches for SFP support and package it for ClearFog. Tested with a
Juniper SFP module.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
MSI interrupts do not seem to be working on mvebu, and they break
ath10k. Since nothing else seems to be using them, especially not
mwlwifi, disable them until we can fix MSI interrupts.
Works around the following issue:
[ 9.001457] ath10k_pci 0000:02:00.0: failed to receive control response completion, polling..
[ 10.001453] ath10k_pci 0000:02:00.0: Service connect timeout
[ 10.007126] ath10k_pci 0000:02:00.0: failed to connect htt (-110)
[ 10.092224] ath10k_pci 0000:02:00.0: could not init core (-110)
[ 10.098177] ath10k_pci 0000:02:00.0: could not probe fw (-110)
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
ar71xx has an init-script for special devices where the ath10k OTP
calibration data is stored on the PCIe card's EEPROM (and thus can only
be read by ath10k). Unfortunately the OTP data uses the default mac
address (= all devices come with the same mac address, which leads to
problems when you have multiple of these devices in the same network).
To work around this the mac address is patched in the firmware during
the first boot of the device. To prevent flash wear this was only done
if the ath10k firmware matched a hardcoded md5sum.
However, if the md5sum does not match this can mean that either the mac
address was already patched (which is fine) - unfortunately it can also
mean that the firmware version was updated without updating the
hardcoded md5sum.
Change the "was the mac address already patched" check to actually
compare the mac address inside the ath10k firmware.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This patch adds support for Cisco's Z1.
Detailed instructions for the flashing the device can
be found in the OpenWrt wiki:
<https://wiki.openwrt.org/toh/meraki/z1>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
kmod-rt2x00-lib and kmod-mac80211 need to be removed, as they depend on
kmod-cfg80211. kmod-rt2800-pci should not be installed anyways.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Add and enable sysupgrade support for clearfog boards, based on how the
brcm2708 target does it.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Add a switch node to clearfog to probe and initialize it on Clearfog
Pro. This make the switch work and allows using all six switch ports.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
If the cpu port is connected through SGMII we need to enable SerDes for
it to work.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
The clearfog u-boot does not initialize the switch at all, so we need to
power up the phys ourselves.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Make the dts file match with what is upstream, to ensure it has the
latest changes and switching to newer kernels is easier.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Some of the PCIe and USB signals use a GPIO expander on I2C on ClearFog,
so enable the driver so that they can be configured to their required
values.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Uboot-mvebu isn't a real package, which will break the image builder
when it tries to install it during the packing step. Instead of cleafog
selecting it through its default packages, make it default to m if the
clearfog profile is selected.
This will ensure it is always build, but never added to the rootfs. This
fixes creating images for clearfog with IB.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
The clearfog image requires u-boot, so package it into KDIR to make sure
it is available in imageBuilder.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Local variable declarations outside of functions are illegal since the Busybox
update to v1.25.0, therfore remove them from the appropriate places.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
