Generates webflash-compatible images for a few RT2880 routers based
on Gemtek OEM boards.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 40551
Depend on lantiq board.
ARV7510 depends on ARV4510 because (according to OpenWrt wiki) both boards are identical except for the unsupported WiFi. Moreover, ARV7510 isn't especifically supported and ARV4510 images valid.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 40544
This patch adds port status information and MIB counters to the ADM6996
switch driver.
The driver supports also the older ADM6996L-variant, but I'm not able to
test this patch on that chip. According to the datasheet the same
registers exist there as well, so I think it should work, but any
feedback is appreciated.
Signed-off-by: Matti Laakso <malaakso at elisanet.fi>
SVN-Revision: 40542
The total ethernet frame length should be written to the hardware
register LTQ_ETOP_IGPLEN instead of just the value of the MTU. This
patch fixes network issues on various Danube boards, especially when
VLAN tagging is enabled.
Signed-off-by: Matti Laakso <malaakso at elisanet.fi>
SVN-Revision: 40541
By default kobs-ng will use the size of /dev/mtd0 for the IMX bootstreams.
This patch allows overriding that size in order to reserve space at the end
of the mtd partition for u-boot.img in the case of using an SPL bootloader.
For example, to flash an SPL bootloader that loads u-boot.img from 0xe0000
(14MB) offset in a 16MB /dev/mtd0:
kobs-ng init -v -x --search_exponent=1 --chip_0_size=0xe00000 SPL
nandwrite --start=0xe00000 --pad /dev/mtd0 u-boot.img
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 40532
The canbus package was recently changed to a more active project. This patch
updates the default package names to include the same functionality as before.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 40531
Remove leftover pieces from package-version-override.mk support
Add a new variable USE_SOURCE_DIR to use a custom build directory.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40527
The /sbin/block binary now requires and additional shared library, therfore set
LD_LIBRARY_PATH accordingly when invoking it from the temporary overlay.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 40526
The RB91x boards are suffering from ethernet packet loss after a cold
boot. The cause of the problem is that the AR8035 PHYs requires special
register settings to work reliably on these boards.
Enable the RGMII TX, RX delays and disable SmartEE functionality of
the AR8035 PHYs. Also enable the RXD delay in the ETH_CFG register
to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40509
Add a patch for the at803x phy driver, in order to be able
to configure some register settings via platform data.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40507
Forgotten patch to fix ethernet for rt2880.
Based on previously submitted patch from Claudio.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 40504
Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg: use zyxel prefix in LED names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40500
With this patch OpenWRT supports the following on the ZyXEL NBG 6716:
-WiFi 2G (ath9k)
-WiFi 5G (ath10k)
-NAND flash
-2 Ethernet interfaces
-USB 2.0
-LEDs including switch
-reasonale defaults at first boot
Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg:
- rename and refresh kernel patch,
- fix a few typos,
- change button key codes,
- use zyxel prefix in LED names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40499
This patch implements support for 802.11s protected mesh wireless networks (using authsae) in the netifd framework.
Until meshd-nl80211 implements a proper -P option for the PID file, this uses shell backgrounding in order to be able to get the PID for the process.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 40497
This is required to make object "session" procedure "access" dump ACLs
when no "object" or no "function" parameters are passed.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 40496
This patch moves ARV7519RW definitions to VR9 section from the AR9 section and removes a whitespace that breaks jffs2 image generation.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 40495
This change does multiple things, all related to enable sparse usage as
a static analysis tool selectable from the OpenWrt configuration:
*add a KERNEL_SPARSE option in the config to add sparse to the kernel
build (through the C=1 option usage)
*add sparse as a new host tools. It will get selected automatically when
the above option will be enabled
Signed-off-by: Mathieu Olivari <mathieu@qca.qualcomm.com>
SVN-Revision: 40490
