This adds support for the TP-LINK CPE210/220/510/520 (Pharos series). These
devices are very similar to the Ubiquiti NanoStations, but with better specs:
faster CPU, more RAM, 2x2 MIMO.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 43385
This patch changes the code of the Wi-Fi On/Off button on the TP-Link WR1043ND v2
from KEY_WLAN to KEY_RFKILL (and renames a few constants to match). The reason
for this change is, that the KEY_WIFI button code is not recognized by the
hotplug subsystem. This means that the userspace is not notified about the
button being pressed which effectively renders it useless.
Signed-off-by: Josef Gajdusek <atx@atx.name>
SVN-Revision: 42922
This patch fixes LED definitions for the DRAGINO2 board.
1. It renames the Router/USB led to System, as it is now marked "SYS" on the board.
2. It gives control of the LAN and WAN leds and some other GPIOs to Linux.
3. It fixes the active_low property for the LAN and WAN leds.
4. It sets up WLAN, LAN and WAN leds in the UCI defaults.
5. It allows usage of the System led by the diag.sh script, so it will be used to indicate boot and failsafe status.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 42897
A typo in the definition for the OM2P reset button disabled its functionality
in OpenWrt. The actual button for these two devices is "1" and not "11".
Signed-off-by: Oren Poleg <oren@poleg.org>
[sven@open-mesh.org: added a commit subject+message]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 42782
Qihoo 360 C301 is a dual band wireless router supports 802.11n and 802.11ac.
Its chipset is AR9344 + AR9882 with two 16MB flashes.
This patch adds its initial support.
v2:
* use mtd_get_mac_ascii to fetch MAC address for ath10k.
* use ath79_register_pci to initialize AR9882.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 42552
While the AR9331 has a gigabit MAC towards the internal switch, the
integrated PHYs however are only 100-base-tx capable. The existing code
however advertieses gigabit capability in the link status word. If you
attach such a PHY to a gigabit capable switch on the remote end, with
some probability it attempts to negotiate gigabit and fails, falling
baco to the AR9331 assuming a 10mbit half-duplex link. This has been
observed quite frequently with the Carambola2 and gigabit capable
switches.
In ath79_register_eth(), "pdata->has_gbit = 1;" is set unconditionally
for both AR9331 ethernet ports. This is most likely wrong. Despite the
two MAC IP cores being gigabit MACs, the MAC for eth1 is connected to a
100base-T PHY via MII. The has_gbit attribute is used in the ethernet
driver to determine the supported link modes.
So either pdata->has_gbit is not set to 1 anymore, or the ethernet
driver needs to be modified to determine the advertised link code word
on another criteria than pdata->has_gbit. This patch implements the
former solution.
Signed-off-by: Harald Welte <laforge@gnumonks.org>
SVN-Revision: 42432
This sets the MAC address of the WLAN interface to the "official" primary MAC
address (the one on the label under the devices, and the one used with the stock
firmware). The MAC address used so far (primary-1) isn't even used at all with
the stock firmware, which sets (primary) on LAN and WLAN and (primary+1) on the
WAN interface (like OpenWrt does with this patch).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 42193
The OpenMesh MR600(v1) can only enable the 2.4G WiFi PHY LED through the
mini-PCIe device. Not configuring the LED pin inside the platform data
makes it impossible to configure it through any standard OpenWrt tool.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 42184
Change list:
* Remove button info on GPIO12, there is no button there.
* Remove nvram mtd partition, as it's not used for anything, saves 64k for user data.
Tested building for carambola2 target.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
SVN-Revision: 41993
this caused factory resets when reboot was pressed
Signed-off-by: Brent Thomson <brentthomson@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41932
Signed-off-by: Jon Suphammer <jon@suphammer.net>
Patchwork: http://patchwork.openwrt.org/patch/5838/
[juhosg:
- fix coding style,
- check the first and the last character of the MAC string
instead of using the strchr() function]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 41622
The GL-Connect GL.iNet v1 router is basically a TP-Link TL-WR703N with
more DRAM/Flash, 2x Ethernet ports and console/GPIO header in the same
small form-factor:
<http://www.gl-inet.com/w/?lang=en>
Moreover, the manufacturer is promoting the OpenWrt usage to replace
the original firmware and proposing patches against both AA and trunk:
<http://www.gl-inet.com/w/?p=398&lang=en>
This is a clean up of the original manufacturer GPLv2 patch by alzhao,
proposed to the list by Mark Janssen.
Signed-off-by: Michel Stempin <michel.stempin@wanadoo.fr>
Signed-off-by: Mark Janssen <mark@sig-io.nl>
Signed-off-by: alzhao <alzhao@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5273/
[juhosg:
- remove user-space and image generation support, will be included
from other patches,
- fix coding style and drop superfluous comment in mach-gl-inet.c,
- rename and refresh kernel patch,
- adjust subject]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 41618
This patch adds support for the MikroTik RouterBOARD SXT Lite.
The new RB911L series is also supported as a result.
v2 of this patch fixes the wmac offset to match what is on the sticker.
v3 refreshes the patch against r41148 and defines the power led as the status led in diag.sh
v4 refreshes the patch against r41353 and fixes the patch path issue to make git am work correctly
v5 selects the kernel config option in the mikrotik profile rather than in the main ar71xx config
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41450
I added WIFI LED support (so now AP blinks nicely), I removed WPS
button GPIO (as it doesn't exist) and changed GPIO for reset button.
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
SVN-Revision: 40976
This board manufactured by HiWiFi has the following features.
- Atheros 9331 SoC.
- 16MB flash and 64MB RAM.
- 4GB eMMC storage via SK6226 USB 2.0 controller.
- 2 LAN and 1 WAN ethernet ports with LEDs on them.
- 3 blue LEDs on the front panel.
- 1 button labeled as "reset".
- Powered by a USB cable.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 40973
Dlink dir-615-e1 can use dir-600-a1's image, but the image can't be
uploaded through dlink's normal firmware update web page.
Add profile for dir-615-e1 so the generated image can be uploaded
through the firmware update web page.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
SVN-Revision: 40969
The RB91x boards are suffering from ethernet packet loss after a cold
boot. The cause of the problem is that the AR8035 PHYs requires special
register settings to work reliably on these boards.
Enable the RGMII TX, RX delays and disable SmartEE functionality of
the AR8035 PHYs. Also enable the RXD delay in the ETH_CFG register
to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40509
With this patch OpenWRT supports the following on the ZyXEL NBG 6716:
-WiFi 2G (ath9k)
-WiFi 5G (ath10k)
-NAND flash
-2 Ethernet interfaces
-USB 2.0
-LEDs including switch
-reasonale defaults at first boot
Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg:
- rename and refresh kernel patch,
- fix a few typos,
- change button key codes,
- use zyxel prefix in LED names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40499
Apart from the wireless chip, the WNDR3700 v4 and the WNDR4300
is the same device. Indicate this in the kernel files.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40479
The 5V power of the USB is controlled by a GPIO pin of
the external WiFi chip. Setup the GPIO bitmasks in the
platform data of the WiFi chip to ensure that the 5V
power gets enabled by the ath9k driver.
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40478
