The uapsd option sets the uapsd_advertisement_enabled flag in hostapd.
The check for phy support is already implemented here in hostapd since 2011:
http://w1.fi/cgit/hostap/commit/?id=70619a5d8a3d32faa43d66bcb1b670cacf0c243e
So this can be safely set to 1 as default.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 43846
In r41872 and r42787 Dynamic VLAN support was reintroduced, but the vlan_bridge
parameter is not read while setting up the config, so the default is used which
is undesirable for some uses.
Signed-off-by: Ben Franske <ben.mm@franske.com>
SVN-Revision: 43473
The wpa_psk_file option offers the possibility to use a different WPA-PSK key for each client. The directive points to a file with the following syntax:
mac_address wpa_passphrase_or_hex_key
Example:
00:11:22:33:44:55 passphrase_for_client_1
00:11:22:33:44:67 passphrase_for_client_2
00:11:22:33:44:89 0123456789abcdef0123456789abcdef0123456789abcdef0123456789abcdef
So it is possible to specify both ASCII passphrases and raw 64-chars hex keys.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 43001
[base-files] shell-scripting: fix wrong usage of '==' operator
normally the '==' is used for invoking a regex parser and is a bashism.
all of the fixes just want to compare a string. the used busybox-ash
will silently "ignore" this mistake, but make it portable/clean at least.
this patch does not change the behavior/logic of the scripts.
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 42911
In r41872 Dynamic VLAN support was reintroduced, but the vlan_naming
parameter is not read while setting up the config, so it always
defaults to 1.
Signed-off-by: Reiner Herrmann <reiner@reiner-h.de>
SVN-Revision: 42787
This patch brings full dynamic vlan support to netifd that existed in hostapd.sh in Attitude Adjustment.
Signed-off-by: Joseph CG Walker <Joe@ChubbyPenguin.net>
[jow@openwrt.org: changed commit message, rebased on top of current hostapd.sh]
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 41872
rsn_preauth is used outside of "case $auth_type", so if it is set
for an EAP-enabled SSID, it would also be set for the following
non-EAP-enabled SSIDs, because it would not be read again.
Signed-off-by: Reiner Herrmann <reiner@reiner-h.de>
SVN-Revision: 41012
`own_ip_addr` is used by hostapd as NAS-IP-Address.
This is used to identify the AP that is requesting the authentication of the
user and could be used to define which AP's can authenticate users.
Some vendors implement only NAS-Identifier or NAS-IP-Address and not both.
This patch adds ownip as an optional parameter in /etc/config/wireless.
Signed-off-by: Thomas Wouters <thomaswouters@gmail.com>
SVN-Revision: 40934
This patch implements support for 802.11s protected mesh wireless networks (using authsae) in the netifd framework.
Until meshd-nl80211 implements a proper -P option for the PID file, this uses shell backgrounding in order to be able to get the PID for the process.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 40497
r39995 introduced a new parameter wps_pbc_in_m1 to wifi wps config, but
apparently did not provide a default value 0.
When that option's non-existing value is later evaluated in
/lib/netifd/hostapd.sh, it causes the "bad number" error to be logged in
syslog if user has not set the wps_pbc_in_m1 option. The error materialises
only if user has enabled wps.
Sat Apr 12 13:25:01 2014 daemon.notice netifd: radio1 (1254): sh: bad number
Sat Apr 12 13:25:01 2014 daemon.notice netifd: radio0 (1253): sh: bad number
Discussion in bug 15508: https://dev.openwrt.org/ticket/15508#comment:3
Error is caused by line 282:
https://dev.openwrt.org/browser/trunk/package/network/services/hostapd/files/netifd.sh#L282
My patch sets the parameter's default value to 0, which does nothing. The
default might also be set a bit later in the function, but this felt like the
most clear place to do that.
Signed-off-by hnyman <hannu.nyman@iki.fi>
SVN-Revision: 40469
Option pbc_in_m1 is being used as a WPS capability discovery
workaround for PBC with Windows 7.
Add possibility to enable this workaround from UCI.
To enable it, turn on wps and set wps_pbc_in_m1 parameter to 1.
Signed-off-by: Pawel Kulakowski <pawel.kulakowski@tieto.com>
SVN-Revision: 39995
This patch introduces 802.11ac support to mac80211 and hostapd. The split of
VHT160 in two 80 MHz bands is not yet supported, since it requires an
additional user supplied parameter for the channel of the second band.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
[sven@open-mesh.com: Rebased patch, merged htmode and vhtmode,
removed special hwmode, replaced uci vht_capab list with overwritable
autoconfig, fixed hostapd integration, fixed commit description, add HT40+/-
for VHT modes, add VHT40 center_freq autoconfig, refactored major parts]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 39456
Introduced by ("netifd: add wireless configuration support and port mac80211 to
the new framework")
Reported-by: René van Weert <r.vanweert@sowifi.com>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
SVN-Revision: 39288
Introduced by ("netifd: add wireless configuration support and port mac80211 to
the new framework")
Reported-by: René van Weert <rene@sowifi.com>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
SVN-Revision: 39231
Currently, in order to configure the authentication daemon in
8021x mode, we need to set wireless.@wifi-iface[0].encryption="wpa"
Though it works it confuses folks as 8021x is using WEP
encryption and not WPA. Therefore the terminology itself is
confusing. This change adds 8021x as a recognized string for 8021x
authentication.
Signed-off-by: Mathieu Olivari <mathieu@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
SVN-Revision: 38339
Setting wireless.@wifi-iface[N].ext_registrar=1 will enable UPNP
advertising and add an external registrar to the interface this vif
belongs to (br-lan if the vif is included in the LAN bridge). By
enabling this we append upnp_iface=xxx to the hostapd config file.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Mathieu Olivari <mathieu@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
SVN-Revision: 38338
Enable CONFIG_WPS2 for hostapd. This is required to support
options like Virtual Push Button in WPS.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
SVN-Revision: 38337
In 2009 OpenWrt's hostapd config added an "auth_cache" boolean
to be used to address a reported issue #12129 [0] on a forum [1].
The reported issue on the ticket is different that the one
described on the forum. The commit was r33359. This change broke
proper RSN preauthentication [2] [3] [4] expectations on hostapd's
configuration for WPA2 and this in turn disabled PMKSA caching and
Opportunistic Key Caching. This change:
* Leaves the "auth_cache" to be used only for WPA networks for those
looking to use this as a workaround to a reported issue but annotates
a warning over its usage.
* Separate "auth_cache" from WPA2 RSN preauthentication, leaving
WPA2 RSN preauthentication to enabled only with "rsn_preauth" with
the expected and recommended settings.
* Adds a new WPA2 RSN preauthentication "rsn_preauth_testing" to
be used when evaluating funcionality for WPA2 RSN preauthentication
with the expected and recommended settings with the only difference
so far with what should be enabled by default to disable Opportunistic
Key Caching.
Disabling the PMKSA cache should mean the STA could not roam off and back
onto the AP that had PMKSA caching disabled and would require a full
authentication cycle. This fixes this for WPA2 networks with
RSN preauthentication enabled.
This change should be applied to AA as well as trunk.
TL DR;
The issue described on the forum has to do with failure of a STA
being able to try to authenticate again with the AP if it failed
its first try. This may have been an issue with hostapd in 2009
but as per some tests I cannot reproduce this today on a WPA2
network.
The issue described on the ticket alludes to a security issue with the
design of using a Radius server to authenticate to an AP. The issue
vaguely alludes to the circumstances of zapping a user, deleting their
authentication credentials to log in to the network, and that if
RSN preauthentication is enabled with PMKSA caching that the user
that was zapped would still be able to authenticate.
Lets treat these as separate issues.
I cannot reproduce the first issue reported on the forums of not
being able to authenticate anymore on a WPA2 network.
The issue reported on the ticket modified WPA2 RSN preauthentication
by adding two fields to the hostapd configuration if auth_cache
was enabled:
* disable_pmksa_caching=1
* okc=0
The first one disables PMKSA authentication cache.
The second one disables Opportunistic Key Caching.
The issue reported on the ticket was fixed by implementing a workaround
in hostapd's configuration. Disabling PMKSA caching breaks proper use
of WPA2 RSN pre authentication. The usage of disable_pmksa_caching=1
prevents hostapd from adding PMKSA entries into its cache when a successful
802.1x authentication occurs. In practice RSN preauthentication would
trigger a STA to perform authentication with other APs on the same SSID,
it would then have its own supplicant PMKSA cache held. If a STA roams
between one AP to another no new authenitcation would need to be performed
as the new AP would already have authenticated the STA. The purpose of the
PMKSA cache on the AP side would be for the AP to use the same PMKID for
a STA when the STA roams off onto another BSSID and later comes back to it.
Disabling Opportunistic Key Caching could help the reported issue
as well but its not the correct place to address this. Opportunistic
Key Caching enables an AP with different interfaces to share the
PMKSA cache. Its a technical enhancement and disabling it would
be useful to let a testing suite properly test for RSN preauthentication
given that otherwise Opportunistic Key Caching would enable an
interface being tested to derive its own derive the PMKSA entry.
In production though okc=1 should be enabled to help with RSN
preauthentication.
The real fix for this particular issue outside of the scope of hostapd's
configuration and it should not be dealt with as a workaround to
its configuration and breaking expected RSN preauthentication and
technical optimizations. Revert this change and enable users to pick
and choose to enable or disable disable_pmksa_caching and okc expecting them
to instead have read clearly more what these do.
As for the core issure ported, the correct place to fix this is to
enable a sort of messaging between the RADIUS server and its peers
so that if caching for authentication is enabled that cache can be
cleared upon user credential updates. Updating a user password
(not just zapping a user) is another possible issue that would need
to be resolved here. Another part of the solution might be to reduce
the cache timing to account for any systematic limitations (RADIUS
server not able to ask peers to clear cache might be
one).
[0] https://dev.openwrt.org/changeset/33359
[1] https://forum.openwrt.org/viewtopic.php?id=19596
[2] http://wireless.kernel.org/en/users/Documentation/hostapd#IEEE_802.11i.2FRSN.2FWPA2_pre-authentication
[3] http://wireless.kernel.org/en/users/Documentation/wpa_supplicant#RSN_preauthentication
[4] http://wiki.openwrt.org/doc/recipes/rsn_preauthentication
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
SVN-Revision: 38336
This adds the eap_reauth_period to be used for modifying
the RADIUS server reauthentication authentication period,
a parameter that gets passed directly to the hostapd
configuration file.
Signed-off-by: Mathieu Olivari <mathieu@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
SVN-Revision: 38334
hostapd supports "Dynamic Authorization Extensions", making it possible
to forcibly disconnect a user by sending it a RADIUS "Disconnect-Request"
packet.
I've added three new variables to enable setting of the
"radius_das_client" and "radius_das_port" variables in the hostapd
configuration, which enable these extensions.
* dae_client - IP of the client that can send disconnect requests
* dae_secret - shared secret for DAE packets
These are combined into the "radius_das_client" option in hostapd.conf
To enable the server, both dae_client and dae_secret must be set.
* dae_port - optional, default value is 3799 as specified in RFC 5176
Signed-off-by: Martijn van de Streek <martijn@vandestreek.net>
SVN-Revision: 37734
Make hostapd.sh correctly handle the macfile uci option.
Such option specifies the macfile name to pass into the
hostapd configuration file. Moreover, if a maclist option
has been specified, copy the macfile before appending new
entries.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
SVN-Revision: 36944
