The bootloader on the WD My Net N750 disables the ports on it's internal
AR8327N switch by powering them down. The stock firmware then brings the
ports back up again by starting the auto negotiation process on each
port.
This fix implements just that.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4615/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39128
This enables us to add fixups to the board specific code for boards that
require special treatment of PHYs on mdio bus reset.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
http://patchwork.openwrt.org/patch/4614/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39127
This enables us to modify the ag71xx_mdio_platform_data from within the
board support files.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4613/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39126
Don't call gpio_keys_remove recursively. Setting the platform
data to NULL triggered an oops on the second iteration, so there was
no infinate loop.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39124
Since the removal of the busybox menuconfig entries, the init scripts
for cron, telnet and ntp are not packaged anymore. Unconditionally
ship them from now on.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 39123
The firewall3 implementation as well as the shell implementation predating it
used to process the tcp_ecnoption as boolean while it actually is an integer.
Change the code to parse tcp_ecn as integer.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 39122
Currently, the AG71XX_RX_PKT_SIZE value limits the received
frame size to 1514/1516 bytes with/without a VLAN header
respectively. However the hardware limit is controlled by
the value the AG71XX_REG_MAC_MFL register which contains
the value of the max_frame_len field.
Compute the RX buffer size from the max_frame_len field
to get rid of the 1514/1516 byte limitation. Also remove
the unused AG71XX_RX_PKT_SIZE definition.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39121
The ar7240_probe function uses the network device name
in the kernel log messages, however the name is not yet
initialized when the ar7240_probe function is called.
Use the mdio bus name in the messages to avoid ugly
log lines like the following one:
eth%d: Found an AR7240/AR9330 built-in switch
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39116
The ag71xx debugfs code uses the network device name
for the device specific debugfs directory. Since r38689
'ar71xx: ag71xx: fix a race involving netdev registration'
the debugfs initialization happens before the ethernet
device gets registered and the network device name contains
'eth%d' at this point. If the board setup code registers
multiple ag71xx devices, the debugfs code tries to create
the device specific dir with the same name which causes
an error like this:
eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
ag71xx: probe of ag71xx.0 failed with error -12
Use the device name for the debugfs directory to avoid the
collisions. Also add an error message and change the return
code if the debugfs_create_dir call fails.
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39115
Some of the Gateworks Ventana boards have CAN bus support, therefore
we will install the userspace utils.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 39113
All Gateworks Ventana boards have a Gateworks System Controller
which emulates the following:
- ds1672 RTC
- pca953x GPIO expander
- hardware monitor
- at24 eeprom
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 39112
This will help with avoiding bogus bug reports caused by stale configs
and bad cases of user tinkering :)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39106
It is only on RB911G-5HPnD and RB912UAG-5HPnD boards.
The LEDs and the USB port is not working yet.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39102
This commit changes the dnsmasq init script to use the interface
status exposed by netifd. The old references to scan_interfaces()
and (indirect) accesses to uci state variables are removed and
replaced with corresponding network_*() calls.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 39101
Use the latest version of the yaffs code. Fetched from the
yaffs2 git tree and it is based on the following commit:
commit bc76682d93955cfb33051beb503ad9f8a5450578
Merge: 3a8580e ffa781d
Author: Charles Manning <cdhmanning@gmail.com>
Date: Thu Jul 11 17:46:25 2013 +1200
Merge branch 'master' of ssh://www.aleph1.co.uk/home/aleph1/git/yaffs2
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39084
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
[juhosg: remove the image generation part until the ethernet
switch issue is resolved]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39078
