The previous update introducing LFS support unconditionally changed the
sprintf() pattern used to print the file modification time to use PRIx64.
Explicitely convert the st_mtime member of the stat struct to uint64_t in
order to avoid type mismatch errors when building for non-64bit targets.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44138
* Fix the ubus plugin to not make its uhttpd_plugin entry symbol
constant as uhttpd needs to modify its list_head member
* Make sure that uhttpd supports large files by using 64bit ints
where appropriate and by passing _FILE_OFFSET_BITS=64 to the build
* Plug a possible memleak in the directory listing code
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44135
Update to latest git head in order to support disabling the build
of upgraded which causes linker errors on avr32.
This also adds some fixes to the ubus system.info and system.board
methods.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44134
Changeset r43049 removed the "062-mips_decompressor_build_fix.patch" which is
still required to properly build the xburst kernel.
Fix the syntax error in the preprocessed code by explicitely undefining the
"memcpy" and "memset" macros prior to declaring the replacements functions.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44133
Using port-based VLANs depends on a non-standard
swconfig parameter, which compilcates things like
LuCI that don't know about it. This patch changes
the default to use 802.1q VLANs internally in the
switch, but without tagging packets since we have
two Ethernet ports.
iperf3 tests indicate no difference in performance
versus port-based VLANs when the CPU port is not
using tags.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 44122
* fix TSO features verify on mt7621 firewrt board
* improve tx clean up. no need to access uncached
memory. also use TX_DTX register instead of
read tx ring DONE bit
* mt7621 need napi weight 64 to get more performance
* remove netif_receive_skb, after kernel version
3.7 tcp4_gro_receive can handle tcp checksum.
on rt2880 use iperf tcp LAN to WAN throughput test.
with gro 135 Mbits/sec. without gro 80.4Mbits/sec.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44118
on mt7621 don't have tx vlan vid registers.
so set FE_REG_FE_DMA_VID_BASE to 0.
set rx vlan offload register to disable.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44117
the rx_buf_size now is 1534 when mtu is 1500.
the ethernet frame with vlan tag and FCS is 1522.
so the buffer is enough.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44116
Add global read-only swconfig attribute "arl_table" to display the
address resolution table.
So far the chip-specific part is implemented for AR8327/AR8337 only
as I don't have the datasheets for the other AR8XXX chips.
Successfully tested on TL-WDR4300 (AR8327rev2)
and TL-WDR4900 (AR8327rev4).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44104
Until a few years ago the page switch wait time was set to msleep(1)
what was changed to usleep_range(1000, 2000) later.
I can not imagine that a low-level operation like switching page
on register level takes so much time.
Most likely the value of 1ms was initially set to check whether
it fixes an issue and then remained w/o further checking whether
also a smaller value would be sufficient.
Now the wait time is set to 5us and I successfully tested this on
AR8327. IMHO 5us should be plenty of time for all supported chips.
However I couldn't test this due to missing hardware.
If other chips should need a longer wait time we can add the
wait time as a parameter to the ar8xxx_chip struct.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44103
Check for switch port link changes and
- flush ATU in case of a change
- report link change via syslog
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44102
The functionality to flush the address translation table contains two bugs
which luckily compensate each other.
1. Just setting the operation is not sufficient to perform the flushing.
The "active" bit needs to be set to actually trigger an action.
For the vtu operations this is implemented correctly.
2. ar8xxx_phy_read_status is called every 2s by the phy state machine
to check for link changes. This would have caused an ATU flush
every 2s.
Fix the chip-specific ATU flush functions and remove the ATU flush call
from ar8xxx_phy_read_status.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44101
The previous implementation of the "host-uniq" option used plain strings for
passing the value to pppd which made it impossible to specify binary data.
Switch the format to a hex encoded string to support binary data.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44094
