Only difference between Generic and P1020 is that P1020
enables SMP with two CPUs in the kernel config.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36454
This upgrades the AT91 target to 3.8.7, and migrates to device tree.
This allows a single kernel to be built for most at91 variants which
simplifies things quite a bit. The immediate result is that all
subtargets are nuked, and any boards without dts files are no longer
supported, though the target now includes more boards than before. The
adc driver was also nuked as 3.8.7 includes a new one under the IIO
subsystem.
Signed-off-by: Adam Porter <porter.adam@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36452
drivers/net/phy/rtl8366_smi.c: In function 'rtl8366_sw_set_vlan_ports':
drivers/net/phy/rtl8366_smi.c:1125:6: warning: 'pvid' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36442
Hello,
this adds the profile for Dlink DIR-615 H1 without the usb default packages
since this router does not have a usb port and while all the needed definitions
for building are already in target/linux/ramips/image/Makefile this also allows
users to select the exact target in RT305x based boards menuconfig for this router
and compile its firmware.
Signed-off-by: Daniel Petre <dani@ip6.ro>
Patchwork: http://patchwork.openwrt.org/patch/3529/
Acked-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36437
Now that ALL5002 and ALL5003 each got their own DTS and board names, remove
the now no longer needed user-space part which previously differentiated between
ALL5002 and ALL5003.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
Patchwork: http://patchwork.openwrt.org/patch/3558/
Acked-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36436
Prior to the switch to 3.8, ALL5002 and ALL5003 boards shared mach-all5002.c.
With the change to DTS, this is no longer accurate, as ALL5002 is based on
Rt3352 SoC while ALL5003 is based on Rt5350 SoC, therefore the corresponding
rt5350.dtsi need to be included for ALL5003.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
Patchwork: http://patchwork.openwrt.org/patch/3557/
Acked-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36435
This board uses a TrendChip SOC with its own RAM/Flash for ADSL support.
We know both SOCs are connected through ethernet and use some kind of protocol for UART communication, but due to the lack of GPL sources we couldn't get it to work. For this reason the network is configured only for LAN.
There are two versions (Chile 8MB and Spain 16MB).
Wiki: http://wiki.openwrt.org/toh/alpha/asl26555
Signed-off-by: Esteban Benito <estebanjbs@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3571/
Acked-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36433
It's needed for dealing with certain UART-to-USB adapters built into
e.g. weather stations, and increases the hid module package only
slightly (e.g. on ar71xx: 35k -> 37k).
Signed-off-by: Danny Baumann <dannybaumann@web.de>
SVN-Revision: 36415
