If the first byte is available in the address mask, use only that one -
set the local bit and xor it with the id << 2. This ensures that there
are no hardware BSSID & BSSID-mask conflicts with devices that have
almost the same MAC address with just a small offset. The MAC address
conflict has been observed in a deployment with some devices from the
same batch when running with multiple interfaces.
If only some bits of the last byte are available, xor the id onto the
last MAC address byte (relevant mostly for Ralink devices).
In other cases (should not happen at this point), use the previous MAC
address offset calculation but without the local bit.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 36353
prepare_generic_squashfs was called twice on the generated images breaking mount_root
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36349
this adds basic support. the bootloader on these units is locked down.
until we have a replacement we can do basic testing with these env variables in uboot.
set update_openwrt erase 0xb0020000 0xb073ffff \;tftp 0x81000000 openwrt-lantiq-xway-VG3503J-squashfs.image\;cp.b 0x81000000 0xb0020000 \$(filesize)
set bootcmd cp.b 0xb0020000 0x80002000 0x400000\; go 0x80002000
unfortunatley the bootloader ignores the bootcmd, so autobooting is not possible yet. you need to call "run bootcmd" by hand after each power cycle.
please note that the vdsl firmware is non redistributable. you can find it in the GPL drop that BT provides.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36315
Update ehci/ohci driver registration to conform to the new platform
drivers.
This fixes missing USB host support in 3.8.x
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 36309
Add support for PMC PM25LQ032 (4MB) SPI Flash used in Hame MPR-A1 and clones.
Signed-off-by: Michel Stempin <michel.stempin@wanadoo.fr>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 36296
3.3 and 3.6 kernels do not make use of the UAPI headers, still they need
to provide an up-to-date switch.h copy for swconfig to build.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 36295
Add Netgear WNCE2001.
This is a small RT3052 device with 4MB spi flash and 32MB ram.
2 built-in antennas, 1x fastE, no USB, reset & wps switch.
On my model the AP/RT switch is unpopulated, but I verified the gpio
mapping for it.
The stock firmware is running an unprotected tftpd which allows you
to read any file from the filesystem.
Serial port is present on testpads (See image on the wiki page).
There are more testpads below the shield near the SoC, which
may have JTAG.
Slight annoyance: The bootloader is checksumming kernel&rootfs, but
can be tricked by zeroing checksum and length fields in the checksum
partition, see
target/linux/ramips/base-files/lib/preinit/04_disable_wnce2001_flash_checksumming
The manufacturer image is very similar to the DAP one, so I slightly
modified mkdapimg to support generating it.
The resulting
openwrt-ramips-rt305x-wnce2001-squashfs-factory-(worldwide|northamerica).bin
can be used to flash from stock to OpenWRT using the stock firmware
upgrade function, without using the serial port.
http://www.netgear.com/landing/wnce2001.aspxhttp://wiki.openwrt.org/toh/netgear/wnce2001
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 36289
