mr/openwrt
2
0
Fork 1
Code Issues 7 Pull Requests Releases Wiki Activity
c0e2282427
openwrt/target/linux/generic-2.4/patches/228-more_usb_fixes.patch
Felix Fietkau 60c1f0f64d finally move buildroot-ng to trunk
2016-03-20 17:29:15 +01:00

862 lines
27 KiB
Diff
Raw Blame History

diff -ur linux.old/drivers/scsi/hosts.c linux.dev/drivers/scsi/hosts.c
--- linux.old/drivers/scsi/hosts.c 2003-06-13 16:51:36.000000000 +0200
+++ linux.dev/drivers/scsi/hosts.c 2006-07-30 12:34:30.000000000 +0200
@@ -107,8 +107,21 @@
if (shn) shn->host_registered = 0;
/* else {} : This should not happen, we should panic here... */
+ /* If we are removing the last host registered, it is safe to reuse
+ * its host number (this avoids "holes" at boot time) (DB)
+ * It is also safe to reuse those of numbers directly below which have
+ * been released earlier (to avoid some holes in numbering).
+ */
+ if(sh->host_no == max_scsi_hosts - 1) {
+ while(--max_scsi_hosts >= next_scsi_host) {
+ shpnt = scsi_hostlist;
+ while(shpnt && shpnt->host_no != max_scsi_hosts - 1)
+ shpnt = shpnt->next;
+ if(shpnt)
+ break;
+ }
+ }
next_scsi_host--;
-
kfree((char *) sh);
}
diff -ur linux.old/drivers/usb/hcd.c linux.dev/drivers/usb/hcd.c
--- linux.old/drivers/usb/hcd.c 2004-04-14 15:05:32.000000000 +0200
+++ linux.dev/drivers/usb/hcd.c 2006-07-30 11:49:06.000000000 +0200
@@ -1105,7 +1105,8 @@
break;
case PIPE_BULK:
allowed |= USB_DISABLE_SPD | USB_QUEUE_BULK
- | USB_ZERO_PACKET | URB_NO_INTERRUPT;
+ | USB_ZERO_PACKET | URB_NO_INTERRUPT
+ | URB_NO_TRANSFER_DMA_MAP;
break;
case PIPE_INTERRUPT:
allowed |= USB_DISABLE_SPD;
@@ -1212,7 +1213,8 @@
urb->setup_packet,
sizeof (struct usb_ctrlrequest),
PCI_DMA_TODEVICE);
- if (urb->transfer_buffer_length != 0)
+ if (urb->transfer_buffer_length != 0
+ && !(urb->transfer_flags & URB_NO_TRANSFER_DMA_MAP))
urb->transfer_dma = pci_map_single (
hcd->pdev,
urb->transfer_buffer,
diff -ur linux.old/drivers/usb/host/ehci-hcd.c linux.dev/drivers/usb/host/ehci-hcd.c
--- linux.old/drivers/usb/host/ehci-hcd.c 2006-07-30 11:31:57.000000000 +0200
+++ linux.dev/drivers/usb/host/ehci-hcd.c 2006-07-30 11:48:14.000000000 +0200
@@ -399,6 +399,27 @@
ehci_mem_cleanup (ehci);
return retval;
}
+
+{
+ int misc_reg;
+ u32 vendor_id;
+
+ pci_read_config_dword (ehci->hcd.pdev, PCI_VENDOR_ID, &vendor_id);
+ if (vendor_id == 0x31041106) {
+ /* VIA 6212 */
+ printk(KERN_INFO "EHCI: Enabling VIA 6212 workarounds\n", misc_reg);
+ pci_read_config_byte(ehci->hcd.pdev, 0x49, &misc_reg);
+ misc_reg &= ~0x20;
+ pci_write_config_byte(ehci->hcd.pdev, 0x49, misc_reg);
+ pci_read_config_byte(ehci->hcd.pdev, 0x49, &misc_reg);
+
+ pci_read_config_byte(ehci->hcd.pdev, 0x4b, &misc_reg);
+ misc_reg |= 0x20;
+ pci_write_config_byte(ehci->hcd.pdev, 0x4b, misc_reg);
+ pci_read_config_byte(ehci->hcd.pdev, 0x4b, &misc_reg);
+ }
+}
+
writel (INTR_MASK, &ehci->regs->intr_enable);
writel (ehci->periodic_dma, &ehci->regs->frame_list);
diff -ur linux.old/drivers/usb/host/ehci-q.c linux.dev/drivers/usb/host/ehci-q.c
--- linux.old/drivers/usb/host/ehci-q.c 2006-07-30 11:31:57.000000000 +0200
+++ linux.dev/drivers/usb/host/ehci-q.c 2006-07-30 12:10:15.000000000 +0200
@@ -791,6 +791,8 @@
writel (cmd, &ehci->regs->command);
ehci->hcd.state = USB_STATE_RUNNING;
/* posted write need not be known to HC yet ... */
+
+ timer_action (ehci, TIMER_IO_WATCHDOG);
}
}
diff -ur linux.old/drivers/usb/host/usb-uhci.c linux.dev/drivers/usb/host/usb-uhci.c
--- linux.old/drivers/usb/host/usb-uhci.c 2004-11-17 12:54:21.000000000 +0100
+++ linux.dev/drivers/usb/host/usb-uhci.c 2006-07-30 12:10:16.000000000 +0200
@@ -2491,7 +2491,7 @@
((urb_priv_t*)urb->hcpriv)->flags=0;
}
- if ((urb->status != -ECONNABORTED) && (urb->status != ECONNRESET) &&
+ if ((urb->status != -ECONNABORTED) && (urb->status != -ECONNRESET) &&
(urb->status != -ENOENT)) {
urb->status = -EINPROGRESS;
@@ -3034,6 +3034,21 @@
pci_set_master(dev);
+ {
+ u8 misc_reg;
+ u32 vendor_id;
+
+ pci_read_config_dword (dev, PCI_VENDOR_ID, &vendor_id);
+ if (vendor_id == 0x30381106) {
+ /* VIA 6212 */
+ printk(KERN_INFO "UHCI: Enabling VIA 6212 workarounds\n");
+ pci_read_config_byte(dev, 0x41, &misc_reg);
+ misc_reg &= ~0x10;
+ pci_write_config_byte(dev, 0x41, misc_reg);
+ pci_read_config_byte(dev, 0x41, &misc_reg);
+ }
+ }
+
/* Search for the IO base address.. */
for (i = 0; i < 6; i++) {
diff -ur linux.old/drivers/usb/storage/transport.c linux.dev/drivers/usb/storage/transport.c
--- linux.old/drivers/usb/storage/transport.c 2005-04-04 03:42:19.000000000 +0200
+++ linux.dev/drivers/usb/storage/transport.c 2006-07-30 12:22:56.000000000 +0200
@@ -54,6 +54,22 @@
#include <linux/sched.h>
#include <linux/errno.h>
#include <linux/slab.h>
+#include <linux/pci.h>
+#include "../hcd.h"
+
+/* These definitions mirror those in pci.h, so they can be used
+ * interchangeably with their PCI_ counterparts */
+enum dma_data_direction {
+ DMA_BIDIRECTIONAL = 0,
+ DMA_TO_DEVICE = 1,
+ DMA_FROM_DEVICE = 2,
+ DMA_NONE = 3,
+};
+
+#define dma_map_sg(d,s,n,dir) pci_map_sg(d,s,n,dir)
+#define dma_unmap_sg(d,s,n,dir) pci_unmap_sg(d,s,n,dir)
+
+
/***********************************************************************
* Helper routines
@@ -554,6 +570,543 @@
return US_BULK_TRANSFER_SHORT;
}
+/*-------------------------------------------------------------------*/
+/**
+ * usb_buffer_unmap_sg - free DMA mapping(s) for a scatterlist
+ * @dev: device to which the scatterlist will be mapped
+ * @pipe: endpoint defining the mapping direction
+ * @sg: the scatterlist to unmap
+ * @n_hw_ents: the positive return value from usb_buffer_map_sg
+ *
+ * Reverses the effect of usb_buffer_map_sg().
+ */
+static void usb_buffer_unmap_sg (struct usb_device *dev, unsigned pipe,
+ struct scatterlist *sg, int n_hw_ents)
+{
+ struct usb_bus *bus;
+ struct usb_hcd *hcd;
+ struct pci_dev *pdev;
+
+ if (!dev
+ || !(bus = dev->bus)
+ || !(hcd = bus->hcpriv)
+ || !(pdev = hcd->pdev)
+ || !pdev->dma_mask)
+ return;
+
+ dma_unmap_sg (pdev, sg, n_hw_ents,
+ usb_pipein (pipe) ? DMA_FROM_DEVICE : DMA_TO_DEVICE);
+}
+
+/**
+ * usb_buffer_map_sg - create scatterlist DMA mapping(s) for an endpoint
+ * @dev: device to which the scatterlist will be mapped
+ * @pipe: endpoint defining the mapping direction
+ * @sg: the scatterlist to map
+ * @nents: the number of entries in the scatterlist
+ *
+ * Return value is either < 0 (indicating no buffers could be mapped), or
+ * the number of DMA mapping array entries in the scatterlist.
+ *
+ * The caller is responsible for placing the resulting DMA addresses from
+ * the scatterlist into URB transfer buffer pointers, and for setting the
+ * URB_NO_TRANSFER_DMA_MAP transfer flag in each of those URBs.
+ *
+ * Top I/O rates come from queuing URBs, instead of waiting for each one
+ * to complete before starting the next I/O. This is particularly easy
+ * to do with scatterlists. Just allocate and submit one URB for each DMA
+ * mapping entry returned, stopping on the first error or when all succeed.
+ * Better yet, use the usb_sg_*() calls, which do that (and more) for you.
+ *
+ * This call would normally be used when translating scatterlist requests,
+ * rather than usb_buffer_map(), since on some hardware (with IOMMUs) it
+ * may be able to coalesce mappings for improved I/O efficiency.
+ *
+ * Reverse the effect of this call with usb_buffer_unmap_sg().
+ */
+static int usb_buffer_map_sg (struct usb_device *dev, unsigned pipe,
+ struct scatterlist *sg, int nents)
+{
+ struct usb_bus *bus;
+ struct usb_hcd *hcd;
+ struct pci_dev *pdev;
+
+ if (!dev
+ || usb_pipecontrol (pipe)
+ || !(bus = dev->bus)
+ || !(hcd = bus->hcpriv)
+ || !(pdev = hcd->pdev)
+ || !pdev->dma_mask)
+ return -1;
+
+ // FIXME generic api broken like pci, can't report errors
+ return dma_map_sg (pdev, sg, nents,
+ usb_pipein (pipe) ? DMA_FROM_DEVICE : DMA_TO_DEVICE);
+}
+
+static void sg_clean (struct usb_sg_request *io)
+{
+ struct usb_hcd *hcd = io->dev->bus->hcpriv;
+ struct pci_dev *pdev = hcd->pdev;
+
+ if (io->urbs) {
+ while (io->entries--)
+ usb_free_urb (io->urbs [io->entries]);
+ kfree (io->urbs);
+ io->urbs = 0;
+ }
+ if (pdev->dma_mask != 0)
+ usb_buffer_unmap_sg (io->dev, io->pipe, io->sg, io->nents);
+ io->dev = 0;
+}
+
+static void sg_complete (struct urb *urb)
+{
+ struct usb_sg_request *io = (struct usb_sg_request *) urb->context;
+
+ spin_lock (&io->lock);
+
+ /* In 2.5 we require hcds' endpoint queues not to progress after fault
+ * reports, until the completion callback (this!) returns. That lets
+ * device driver code (like this routine) unlink queued urbs first,
+ * if it needs to, since the HC won't work on them at all. So it's
+ * not possible for page N+1 to overwrite page N, and so on.
+ *
+ * That's only for "hard" faults; "soft" faults (unlinks) sometimes
+ * complete before the HCD can get requests away from hardware,
+ * though never during cleanup after a hard fault.
+ */
+ if (io->status
+ && (io->status != -ECONNRESET
+ || urb->status != -ECONNRESET)
+ && urb->actual_length) {
+ US_DEBUGP("Error: %s ep%d%s scatterlist error %d/%d\n",
+ io->dev->devpath,
+ usb_pipeendpoint (urb->pipe),
+ usb_pipein (urb->pipe) ? "in" : "out",
+ urb->status, io->status);
+ // BUG ();
+ }
+
+ if (urb->status && urb->status != -ECONNRESET) {
+ int i, found, status;
+
+ io->status = urb->status;
+
+ /* the previous urbs, and this one, completed already.
+ * unlink pending urbs so they won't rx/tx bad data.
+ */
+ for (i = 0, found = 0; i < io->entries; i++) {
+ if (!io->urbs [i])
+ continue;
+ if (found) {
+ status = usb_unlink_urb (io->urbs [i]);
+ if (status != -EINPROGRESS && status != -EBUSY)
+ US_DEBUGP("Error: %s, unlink --> %d\n", __FUNCTION__, status);
+ } else if (urb == io->urbs [i])
+ found = 1;
+ }
+ }
+ urb->dev = 0;
+
+ /* on the last completion, signal usb_sg_wait() */
+ io->bytes += urb->actual_length;
+ io->count--;
+ if (!io->count)
+ complete (&io->complete);
+
+ spin_unlock (&io->lock);
+}
+
+/**
+ * usb_sg_init - initializes scatterlist-based bulk/interrupt I/O request
+ * @io: request block being initialized. until usb_sg_wait() returns,
+ * treat this as a pointer to an opaque block of memory,
+ * @dev: the usb device that will send or receive the data
+ * @pipe: endpoint "pipe" used to transfer the data
+ * @period: polling rate for interrupt endpoints, in frames or
+ * (for high speed endpoints) microframes; ignored for bulk
+ * @sg: scatterlist entries
+ * @nents: how many entries in the scatterlist
+ * @length: how many bytes to send from the scatterlist, or zero to
+ * send every byte identified in the list.
+ * @mem_flags: SLAB_* flags affecting memory allocations in this call
+ *
+ * Returns zero for success, else a negative errno value. This initializes a
+ * scatter/gather request, allocating resources such as I/O mappings and urb
+ * memory (except maybe memory used by USB controller drivers).
+ *
+ * The request must be issued using usb_sg_wait(), which waits for the I/O to
+ * complete (or to be canceled) and then cleans up all resources allocated by
+ * usb_sg_init().
+ *
+ * The request may be canceled with usb_sg_cancel(), either before or after
+ * usb_sg_wait() is called.
+ */
+int usb_sg_init (
+ struct usb_sg_request *io,
+ struct usb_device *dev,
+ unsigned pipe,
+ unsigned period,
+ struct scatterlist *sg,
+ int nents,
+ size_t length,
+ int mem_flags
+)
+{
+ int i;
+ int urb_flags;
+ int dma;
+ struct usb_hcd *hcd;
+
+ hcd = dev->bus->hcpriv;
+
+ if (!io || !dev || !sg
+ || usb_pipecontrol (pipe)
+ || usb_pipeisoc (pipe)
+ || nents <= 0)
+ return -EINVAL;
+
+ spin_lock_init (&io->lock);
+ io->dev = dev;
+ io->pipe = pipe;
+ io->sg = sg;
+ io->nents = nents;
+
+ /* not all host controllers use DMA (like the mainstream pci ones);
+ * they can use PIO (sl811) or be software over another transport.
+ */
+ dma = (hcd->pdev->dma_mask != 0);
+ if (dma)
+ io->entries = usb_buffer_map_sg (dev, pipe, sg, nents);
+ else
+ io->entries = nents;
+
+ /* initialize all the urbs we'll use */
+ if (io->entries <= 0)
+ return io->entries;
+
+ io->count = 0;
+ io->urbs = kmalloc (io->entries * sizeof *io->urbs, mem_flags);
+ if (!io->urbs)
+ goto nomem;
+
+ urb_flags = USB_ASYNC_UNLINK | URB_NO_INTERRUPT | URB_NO_TRANSFER_DMA_MAP;
+ if (usb_pipein (pipe))
+ urb_flags |= URB_SHORT_NOT_OK;
+
+ for (i = 0; i < io->entries; i++, io->count = i) {
+ unsigned len;
+
+ io->urbs [i] = usb_alloc_urb (0);
+ if (!io->urbs [i]) {
+ io->entries = i;
+ goto nomem;
+ }
+
+ io->urbs [i]->dev = 0;
+ io->urbs [i]->pipe = pipe;
+ io->urbs [i]->interval = period;
+ io->urbs [i]->transfer_flags = urb_flags;
+
+ io->urbs [i]->complete = sg_complete;
+ io->urbs [i]->context = io;
+ io->urbs [i]->status = -EINPROGRESS;
+ io->urbs [i]->actual_length = 0;
+
+ if (dma) {
+ /* hc may use _only_ transfer_dma */
+ io->urbs [i]->transfer_dma = sg_dma_address (sg + i);
+ len = sg_dma_len (sg + i);
+ } else {
+ /* hc may use _only_ transfer_buffer */
+ io->urbs [i]->transfer_buffer =
+ page_address (sg [i].page) + sg [i].offset;
+ len = sg [i].length;
+ }
+
+ if (length) {
+ len = min_t (unsigned, len, length);
+ length -= len;
+ if (length == 0)
+ io->entries = i + 1;
+ }
+ io->urbs [i]->transfer_buffer_length = len;
+ }
+ io->urbs [--i]->transfer_flags &= ~URB_NO_INTERRUPT;
+
+ /* transaction state */
+ io->status = 0;
+ io->bytes = 0;
+ init_completion (&io->complete);
+ return 0;
+
+nomem:
+ sg_clean (io);
+ return -ENOMEM;
+}
+
+/**
+ * usb_sg_cancel - stop scatter/gather i/o issued by usb_sg_wait()
+ * @io: request block, initialized with usb_sg_init()
+ *
+ * This stops a request after it has been started by usb_sg_wait().
+ * It can also prevents one initialized by usb_sg_init() from starting,
+ * so that call just frees resources allocated to the request.
+ */
+void usb_sg_cancel (struct usb_sg_request *io)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave (&io->lock, flags);
+
+ /* shut everything down, if it didn't already */
+ if (!io->status) {
+ int i;
+
+ io->status = -ECONNRESET;
+ for (i = 0; i < io->entries; i++) {
+ int retval;
+
+ if (!io->urbs [i]->dev)
+ continue;
+ retval = usb_unlink_urb (io->urbs [i]);
+ if (retval != -EINPROGRESS && retval != -EBUSY)
+ US_DEBUGP("WARNING: %s, unlink --> %d\n", __FUNCTION__, retval);
+ }
+ }
+ spin_unlock_irqrestore (&io->lock, flags);
+}
+
+/**
+ * usb_sg_wait - synchronously execute scatter/gather request
+ * @io: request block handle, as initialized with usb_sg_init().
+ * some fields become accessible when this call returns.
+ * Context: !in_interrupt ()
+ *
+ * This function blocks until the specified I/O operation completes. It
+ * leverages the grouping of the related I/O requests to get good transfer
+ * rates, by queueing the requests. At higher speeds, such queuing can
+ * significantly improve USB throughput.
+ *
+ * There are three kinds of completion for this function.
+ * (1) success, where io->status is zero. The number of io->bytes
+ * transferred is as requested.
+ * (2) error, where io->status is a negative errno value. The number
+ * of io->bytes transferred before the error is usually less
+ * than requested, and can be nonzero.
+ * (3) cancelation, a type of error with status -ECONNRESET that
+ * is initiated by usb_sg_cancel().
+ *
+ * When this function returns, all memory allocated through usb_sg_init() or
+ * this call will have been freed. The request block parameter may still be
+ * passed to usb_sg_cancel(), or it may be freed. It could also be
+ * reinitialized and then reused.
+ *
+ * Data Transfer Rates:
+ *
+ * Bulk transfers are valid for full or high speed endpoints.
+ * The best full speed data rate is 19 packets of 64 bytes each
+ * per frame, or 1216 bytes per millisecond.
+ * The best high speed data rate is 13 packets of 512 bytes each
+ * per microframe, or 52 KBytes per millisecond.
+ *
+ * The reason to use interrupt transfers through this API would most likely
+ * be to reserve high speed bandwidth, where up to 24 KBytes per millisecond
+ * could be transferred. That capability is less useful for low or full
+ * speed interrupt endpoints, which allow at most one packet per millisecond,
+ * of at most 8 or 64 bytes (respectively).
+ */
+void usb_sg_wait (struct usb_sg_request *io)
+{
+ int i, entries = io->entries;
+
+ /* queue the urbs. */
+ spin_lock_irq (&io->lock);
+ for (i = 0; i < entries && !io->status; i++) {
+ int retval;
+
+ io->urbs [i]->dev = io->dev;
+ retval = usb_submit_urb (io->urbs [i]);
+
+ /* after we submit, let completions or cancelations fire;
+ * we handshake using io->status.
+ */
+ spin_unlock_irq (&io->lock);
+ switch (retval) {
+ /* maybe we retrying will recover */
+ case -ENXIO: // hc didn't queue this one
+ case -EAGAIN:
+ case -ENOMEM:
+ io->urbs [i]->dev = 0;
+ retval = 0;
+ i--;
+ yield ();
+ break;
+
+ /* no error? continue immediately.
+ *
+ * NOTE: to work better with UHCI (4K I/O buffer may
+ * need 3K of TDs) it may be good to limit how many
+ * URBs are queued at once; N milliseconds?
+ */
+ case 0:
+ cpu_relax ();
+ break;
+
+ /* fail any uncompleted urbs */
+ default:
+ spin_lock_irq (&io->lock);
+ io->count -= entries - i;
+ if (io->status == -EINPROGRESS)
+ io->status = retval;
+ if (io->count == 0)
+ complete (&io->complete);
+ spin_unlock_irq (&io->lock);
+
+ io->urbs [i]->dev = 0;
+ io->urbs [i]->status = retval;
+
+ US_DEBUGP("%s, submit --> %d\n", __FUNCTION__, retval);
+ usb_sg_cancel (io);
+ }
+ spin_lock_irq (&io->lock);
+ if (retval && io->status == -ECONNRESET)
+ io->status = retval;
+ }
+ spin_unlock_irq (&io->lock);
+
+ /* OK, yes, this could be packaged as non-blocking.
+ * So could the submit loop above ... but it's easier to
+ * solve neither problem than to solve both!
+ */
+ wait_for_completion (&io->complete);
+
+ sg_clean (io);
+}
+
+/*
+ * Interpret the results of a URB transfer
+ *
+ * This function prints appropriate debugging messages, clears halts on
+ * non-control endpoints, and translates the status to the corresponding
+ * USB_STOR_XFER_xxx return code.
+ */
+static int interpret_urb_result(struct us_data *us, unsigned int pipe,
+ unsigned int length, int result, unsigned int partial)
+{
+ US_DEBUGP("Status code %d; transferred %u/%u\n",
+ result, partial, length);
+ switch (result) {
+
+ /* no error code; did we send all the data? */
+ case 0:
+ if (partial != length) {
+ US_DEBUGP("-- short transfer\n");
+ return USB_STOR_XFER_SHORT;
+ }
+
+ US_DEBUGP("-- transfer complete\n");
+ return USB_STOR_XFER_GOOD;
+
+ /* stalled */
+ case -EPIPE:
+ /* for control endpoints, (used by CB[I]) a stall indicates
+ * a failed command */
+ if (usb_pipecontrol(pipe)) {
+ US_DEBUGP("-- stall on control pipe\n");
+ return USB_STOR_XFER_STALLED;
+ }
+
+ /* for other sorts of endpoint, clear the stall */
+ US_DEBUGP("clearing endpoint halt for pipe 0x%x\n", pipe);
+ if (usb_stor_clear_halt(us, pipe) < 0)
+ return USB_STOR_XFER_ERROR;
+ return USB_STOR_XFER_STALLED;
+
+ /* timeout or excessively long NAK */
+ case -ETIMEDOUT:
+ US_DEBUGP("-- timeout or NAK\n");
+ return USB_STOR_XFER_ERROR;
+
+ /* babble - the device tried to send more than we wanted to read */
+ case -EOVERFLOW:
+ US_DEBUGP("-- babble\n");
+ return USB_STOR_XFER_LONG;
+
+ /* the transfer was cancelled by abort, disconnect, or timeout */
+ case -ECONNRESET:
+ US_DEBUGP("-- transfer cancelled\n");
+ return USB_STOR_XFER_ERROR;
+
+ /* short scatter-gather read transfer */
+ case -EREMOTEIO:
+ US_DEBUGP("-- short read transfer\n");
+ return USB_STOR_XFER_SHORT;
+
+ /* abort or disconnect in progress */
+ case -EIO:
+ US_DEBUGP("-- abort or disconnect in progress\n");
+ return USB_STOR_XFER_ERROR;
+
+ /* the catch-all error case */
+ default:
+ US_DEBUGP("-- unknown error\n");
+ return USB_STOR_XFER_ERROR;
+ }
+}
+
+/*
+ * Transfer a scatter-gather list via bulk transfer
+ *
+ * This function does basically the same thing as usb_stor_bulk_msg()
+ * above, but it uses the usbcore scatter-gather library.
+ */
+int usb_stor_bulk_transfer_sglist(struct us_data *us, unsigned int pipe,
+ struct scatterlist *sg, int num_sg, unsigned int length,
+ unsigned int *act_len)
+{
+ int result;
+
+ /* don't submit s-g requests during abort/disconnect processing */
+ if (us->flags & ABORTING_OR_DISCONNECTING)
+ return USB_STOR_XFER_ERROR;
+
+ /* initialize the scatter-gather request block */
+ US_DEBUGP("%s: xfer %u bytes, %d entries\n", __FUNCTION__,
+ length, num_sg);
+ result = usb_sg_init(&us->current_sg, us->pusb_dev, pipe, 0,
+ sg, num_sg, length, SLAB_NOIO);
+ if (result) {
+ US_DEBUGP("usb_sg_init returned %d\n", result);
+ return USB_STOR_XFER_ERROR;
+ }
+
+ /* since the block has been initialized successfully, it's now
+ * okay to cancel it */
+ set_bit(US_FLIDX_SG_ACTIVE, &us->flags);
+
+ /* did an abort/disconnect occur during the submission? */
+ if (us->flags & ABORTING_OR_DISCONNECTING) {
+
+ /* cancel the request, if it hasn't been cancelled already */
+ if (test_and_clear_bit(US_FLIDX_SG_ACTIVE, &us->flags)) {
+ US_DEBUGP("-- cancelling sg request\n");
+ usb_sg_cancel(&us->current_sg);
+ }
+ }
+
+ /* wait for the completion of the transfer */
+ usb_sg_wait(&us->current_sg);
+ clear_bit(US_FLIDX_SG_ACTIVE, &us->flags);
+
+ result = us->current_sg.status;
+ if (act_len)
+ *act_len = us->current_sg.bytes;
+ return interpret_urb_result(us, pipe, length, result,
+ us->current_sg.bytes);
+}
+
/*
* Transfer an entire SCSI command's worth of data payload over the bulk
* pipe.
@@ -569,6 +1122,8 @@
struct scatterlist *sg;
unsigned int total_transferred = 0;
unsigned int transfer_amount;
+ unsigned int partial;
+ unsigned int pipe;
/* calculate how much we want to transfer */
transfer_amount = usb_stor_transfer_length(srb);
@@ -585,23 +1140,34 @@
* make the appropriate requests for each, until done
*/
sg = (struct scatterlist *) srb->request_buffer;
- for (i = 0; i < srb->use_sg; i++) {
-
- /* transfer the lesser of the next buffer or the
- * remaining data */
- if (transfer_amount - total_transferred >=
- sg[i].length) {
- result = usb_stor_transfer_partial(us,
- sg[i].address, sg[i].length);
- total_transferred += sg[i].length;
- } else
- result = usb_stor_transfer_partial(us,
- sg[i].address,
- transfer_amount - total_transferred);
-
- /* if we get an error, end the loop here */
- if (result)
- break;
+ if (us->pusb_dev->speed == USB_SPEED_HIGH) {
+ /* calculate the appropriate pipe information */
+ if (us->srb->sc_data_direction == SCSI_DATA_READ)
+ pipe = usb_rcvbulkpipe(us->pusb_dev, us->ep_in);
+ else
+ pipe = usb_sndbulkpipe(us->pusb_dev, us->ep_out);
+ /* use the usb core scatter-gather primitives */
+ result = usb_stor_bulk_transfer_sglist(us, pipe,
+ sg, srb->use_sg, transfer_amount, &partial);
+ } else {
+ for (i = 0; i < srb->use_sg; i++) {
+
+ /* transfer the lesser of the next buffer or the
+ * remaining data */
+ if (transfer_amount - total_transferred >=
+ sg[i].length) {
+ result = usb_stor_transfer_partial(us,
+ sg[i].address, sg[i].length);
+ total_transferred += sg[i].length;
+ } else
+ result = usb_stor_transfer_partial(us,
+ sg[i].address,
+ transfer_amount - total_transferred);
+
+ /* if we get an error, end the loop here */
+ if (result)
+ break;
+ }
}
}
else
diff -ur linux.old/drivers/usb/storage/transport.h linux.dev/drivers/usb/storage/transport.h
--- linux.old/drivers/usb/storage/transport.h 2003-08-25 13:44:42.000000000 +0200
+++ linux.dev/drivers/usb/storage/transport.h 2006-07-30 12:10:16.000000000 +0200
@@ -127,6 +127,16 @@
#define US_BULK_TRANSFER_ABORTED 3 /* transfer canceled */
/*
+ * usb_stor_bulk_transfer_xxx() return codes, in order of severity
+ */
+
+#define USB_STOR_XFER_GOOD 0 /* good transfer */
+#define USB_STOR_XFER_SHORT 1 /* transferred less than expected */
+#define USB_STOR_XFER_STALLED 2 /* endpoint stalled */
+#define USB_STOR_XFER_LONG 3 /* device tried to send too much */
+#define USB_STOR_XFER_ERROR 4 /* transfer died in the middle */
+
+/*
* Transport return codes
*/
diff -ur linux.old/drivers/usb/storage/usb.h linux.dev/drivers/usb/storage/usb.h
--- linux.old/drivers/usb/storage/usb.h 2005-04-04 03:42:20.000000000 +0200
+++ linux.dev/drivers/usb/storage/usb.h 2006-07-30 12:11:06.000000000 +0200
@@ -111,6 +111,60 @@
typedef void (*proto_cmnd)(Scsi_Cmnd*, struct us_data*);
typedef void (*extra_data_destructor)(void *); /* extra data destructor */
+/* Dynamic flag definitions: used in set_bit() etc. */
+#define US_FLIDX_URB_ACTIVE 18 /* 0x00040000 current_urb is in use */
+#define US_FLIDX_SG_ACTIVE 19 /* 0x00080000 current_sg is in use */
+#define US_FLIDX_ABORTING 20 /* 0x00100000 abort is in progress */
+#define US_FLIDX_DISCONNECTING 21 /* 0x00200000 disconnect in progress */
+#define ABORTING_OR_DISCONNECTING ((1UL << US_FLIDX_ABORTING) | \
+ (1UL << US_FLIDX_DISCONNECTING))
+#define US_FLIDX_RESETTING 22 /* 0x00400000 device reset in progress */
+
+/* processing state machine states */
+#define US_STATE_IDLE 1
+#define US_STATE_RUNNING 2
+#define US_STATE_RESETTING 3
+#define US_STATE_ABORTING 4
+
+/**
+ * struct usb_sg_request - support for scatter/gather I/O
+ * @status: zero indicates success, else negative errno
+ * @bytes: counts bytes transferred.
+ *
+ * These requests are initialized using usb_sg_init(), and then are used
+ * as request handles passed to usb_sg_wait() or usb_sg_cancel(). Most
+ * members of the request object aren't for driver access.
+ *
+ * The status and bytecount values are valid only after usb_sg_wait()
+ * returns. If the status is zero, then the bytecount matches the total
+ * from the request.
+ *
+ * After an error completion, drivers may need to clear a halt condition
+ * on the endpoint.
+ */
+struct usb_sg_request {
+ int status;
+ size_t bytes;
+
+ /*
+ * members below are private to usbcore,
+ * and are not provided for driver access!
+ */
+ spinlock_t lock;
+
+ struct usb_device *dev;
+ int pipe;
+ struct scatterlist *sg;
+ int nents;
+
+ int entries;
+ struct urb **urbs;
+
+ int count;
+ struct completion complete;
+};
+
+
/* we allocate one of these for every device that we remember */
struct us_data {
struct us_data *next; /* next device */
@@ -171,6 +225,7 @@
struct urb *current_urb; /* non-int USB requests */
struct completion current_done; /* the done flag */
unsigned int tag; /* tag for bulk CBW/CSW */
+ struct usb_sg_request current_sg; /* scatter-gather req. */
/* the semaphore for sleeping the control thread */
struct semaphore sema; /* to sleep thread on */
diff -ur linux.old/include/linux/usb.h linux.dev/include/linux/usb.h
--- linux.old/include/linux/usb.h 2004-11-17 12:54:22.000000000 +0100
+++ linux.dev/include/linux/usb.h 2006-07-30 12:19:19.000000000 +0200
@@ -483,6 +483,8 @@
#define URB_NO_INTERRUPT 0x0080 /* HINT: no non-error interrupt needed */
/* ... less overhead for QUEUE_BULK */
#define USB_TIMEOUT_KILLED 0x1000 // only set by HCD!
+#define URB_NO_TRANSFER_DMA_MAP 0x0400 /* urb->transfer_dma valid on submit */
+#define URB_NO_SETUP_DMA_MAP 0x0800 /* urb->setup_dma valid on submit */
struct iso_packet_descriptor
{
Reference in New Issue View Git Blame Copy Permalink