- Use common OpenWrt blink patterns instead of custom ones
- Add preinit_regular hook
- Handle the TDW89X0 that does not have a configurable power LED
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 47914
This patch configures the correct ath9k WLAN LED polarity for the TDW8970.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 47913
The TDW8970 has a AR9381, which is the bgn 3x3:3 variant of the AR938x family.
The TDW8980 has a AR9287, which is the bgn 2x2:2 variant of the AR928x family.
This means that the chip for both routers is 2.4 GHz only.
Anyway, the manufacturer didn't disable the 5 GHz band in the EEPROM partition
(at least on my TDW8970).
So this patch disables the 5 GHz band.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 47912
Zero config value for default memory region means 'memory', not
not 'disabled' according to 'Control Registers Of The Coherency
Manager' manual.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47906
Since now we hopefully setup memory regions properly we no longer need this hack.
Tested and works on ubnt-erx.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47905
Only compile tested since I do not have any hardware with
devices on pcie bus.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47904
- CONFIG_IFX_CLI is unused, couldn't find any reference to this config variable
- use disable-feature instead of enable-feature=no
- reorder configure args to have depending args together
- remove configure args which set the default value
- group enable-model and configure args which enable or disable features that
are covered by the feature set
The config.log contains the same values as before. The vdsl_cpe_control binary
has the same checksum as before.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47888
The typicial feature set doesn't include "DSL PM showtime counters support"
(INCLUDE_DSL_CPE_PM_SHOWTIME_COUNTERS). This feature provides the
vdsl_cpe_control command 'pmccsg', which is used by 'dsl_control status' to get
the line uptime.
The binary size increases to 103912 byte (+4256 byte) uncompressed.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47887
This router is based on MT7621 SoC, no wifi, no usb, nand.
Works:
* Boots.
* Ethernet.
* Switch.
* Button (reset).
* Flashing OpenWrt from stock firmware.
* Upgrading OpenWrt.
Doesn't work:
* No GPIO leds. All leds are controlled by switch,
but stock firmware was able to control them.
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
nand/spi drivers do not support pin sharing,
so it is not accessable and disabled. Stock
firmware could read it and it was empty.
* PoE out.
Router has serial pins populated. If looking at the top
of the router, then counting from Eth sockets pins go as:
'GND, RX, TX, GND'. 3.3v, 57600.
U-boot bootloader supports tftpboot, controlled from serial.
This router has two kernel partitions: 'live' and 'backup'.
They are swapped during flashing (on both stock and OpenWrt).
Active partition is controlled by a flag in a factory partition.
U-boot has custom command to switch active kernel partition.
Kernel partitions are 'bare flash' 3MB. Stock bootloader has
no UBI support. Stock rootfs is UBIFS.
Flashing procedure.
Stock firmware uses custom kernel patch to mount squashfs
from a file that is located on UBIFS volume. This makes wiping
out this volume from within stock firmware difficult.
Instead this patch builds image that is flashable by stock firmware
and contains initrams image (with minimal set of packages
to fit into kernel partition). Once this is flashed one can reboot
into initramfs OpenWrt and use sysupgrade to flash OpenWrt including
rootfs into nand.
Note: factory image is only built if initramfs image is enabled.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47881
Add 'platform_nand_pre_upgrade' callback to allow platform specific
preparation right before flashinng, when already in ramdisk.
Example uses might be setting correct values for CI_{KERNPART,UBIPART}.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47879
This patch adds support for Cisco's MR18.
Detailed instructions for the flashing the device can
be found in the OpenWrt forum thread:
<https://forum.openwrt.org/viewtopic.php?id=59248>
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47878
Partitions defined in parent dtsi cannot be undefined in children.
This moves partitions defined in mt7621.dtsi into board's device tree.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47876
* Switches clocksource to gic timer.
* Moves frequency definitions to dtsi since frequency was hardcoded anyway
Will work on proper frequency detection later.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47875
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47867
mostly implicit defines due to missing includes plus one const that
shouldn't be one.
Signed-off-by: Felix Kaechele <felix@kaechele.ca>
SVN-Revision: 47865
