Use a different length for calculating the nvram checksum on hauwei
boards. Fixes boot on HW553 and HW556.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 35533
The first preinit script 03_do_brcm63xx.sh does the right job of
exporting variables for the other subsequent preinit scripts to use
them.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35504
Actually this board is the very same as the rta770bw,
where the additional 'b' within the name just
indicates 'Annex B'. The ADSL Modem itself is able
to handle both, Annex A as well as Annex B -
the loaded firmware makes the only difference
SVN-Revision: 35500
Switch to using the B53 switch driver where appropriate.
Use a non-tagged default config where it isn't confirmed to be
working.
Remove the switch configuration in preinit as the switch will now
be configured by the driver to use port isolation to prevent leakage
between lan and wan.
While at it, also provide a switch config for Neufbox 6.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 35307
The SPI driver is needed for supporting to boot from SPI flash on BCM6358
and BCM6368, and for SPI connected switches.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 35304
Allow bcm63xxpart to receive a caldata offset if calibration data is contained in flash.
Tested-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
SVN-Revision: 35010
This patch adds support for defining rt2x00 eeprom data.
This eeprom data can be extracted from flash or loaded directly from a firmware file.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 34322
Some boards need specifying LED pin in order to get it working.
For example, in board HW556 (Huawei HG556a) "led_pin" must be "2".
By default led_pin is "0", so dsl_274xb_rev_f is changed to "-1".
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 34321
* Accept transfers without bits_per_word set.
* Work around the inability of the hardware of keeping CS asserted.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 34320
This reverts commit r34230, as it is causing build failures:
make[3] -C package/mtd compile
imagetag.c:35:32: fatal error: linux/bcm963xx_tag.h: No such file or directory
compilation terminated.
make[4]: *** [imagetag.o] Error 1
Any patches modifying exported kernel headers need to reside in generic
as toolchain/kernel-headers only applies generic patches.
SVN-Revision: 34255
Fixes the following error:
drivers/usb/host/ohci-bcm63xx.c: In function 'ohci_bcm63xx_start':
drivers/usb/host/ohci-bcm63xx.c:33:3: error: implicit declaration of function 'err' [-Werror=implicit-function-declaration]
Reported-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 34138
Some ath9k caldatas need to be "endian checked".
This patch allows selecting wether to enable endian check or not.
Endian check is disabled by default.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 34105
