MSI interrupts do not seem to be working on mvebu, and they break
ath10k. Since nothing else seems to be using them, especially not
mwlwifi, disable them until we can fix MSI interrupts.
Works around the following issue:
[ 9.001457] ath10k_pci 0000:02:00.0: failed to receive control response completion, polling..
[ 10.001453] ath10k_pci 0000:02:00.0: Service connect timeout
[ 10.007126] ath10k_pci 0000:02:00.0: failed to connect htt (-110)
[ 10.092224] ath10k_pci 0000:02:00.0: could not init core (-110)
[ 10.098177] ath10k_pci 0000:02:00.0: could not probe fw (-110)
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
ar71xx has an init-script for special devices where the ath10k OTP
calibration data is stored on the PCIe card's EEPROM (and thus can only
be read by ath10k). Unfortunately the OTP data uses the default mac
address (= all devices come with the same mac address, which leads to
problems when you have multiple of these devices in the same network).
To work around this the mac address is patched in the firmware during
the first boot of the device. To prevent flash wear this was only done
if the ath10k firmware matched a hardcoded md5sum.
However, if the md5sum does not match this can mean that either the mac
address was already patched (which is fine) - unfortunately it can also
mean that the firmware version was updated without updating the
hardcoded md5sum.
Change the "was the mac address already patched" check to actually
compare the mac address inside the ath10k firmware.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This patch adds support for Cisco's Z1.
Detailed instructions for the flashing the device can
be found in the OpenWrt wiki:
<https://wiki.openwrt.org/toh/meraki/z1>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
kmod-rt2x00-lib and kmod-mac80211 need to be removed, as they depend on
kmod-cfg80211. kmod-rt2800-pci should not be installed anyways.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Add and enable sysupgrade support for clearfog boards, based on how the
brcm2708 target does it.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Add a switch node to clearfog to probe and initialize it on Clearfog
Pro. This make the switch work and allows using all six switch ports.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
If the cpu port is connected through SGMII we need to enable SerDes for
it to work.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
The clearfog u-boot does not initialize the switch at all, so we need to
power up the phys ourselves.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Make the dts file match with what is upstream, to ensure it has the
latest changes and switching to newer kernels is easier.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Some of the PCIe and USB signals use a GPIO expander on I2C on ClearFog,
so enable the driver so that they can be configured to their required
values.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Uboot-mvebu isn't a real package, which will break the image builder
when it tries to install it during the packing step. Instead of cleafog
selecting it through its default packages, make it default to m if the
clearfog profile is selected.
This will ensure it is always build, but never added to the rootfs. This
fixes creating images for clearfog with IB.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
The clearfog image requires u-boot, so package it into KDIR to make sure
it is available in imageBuilder.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Local variable declarations outside of functions are illegal since the Busybox
update to v1.25.0, therfore remove them from the appropriate places.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Older busybox versions allowed using the local keyword outside of
functions, whereas 1.25.0 (which was introduced in 06fa1c46fc) do not
allow this anymore (leading to the following error when executing the
script: "file: local: line nn: not in a function").
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Older busybox versions allowed using the local keyword outside of
functions, whereas 1.25.0 (which was introduced in 06fa1c46fc) do not
allow this anymore (leading to the following error when executing the
script: "file: local: line nn: not in a function").
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Some devices (like the Cisco Meraki Z1 Cloud Managed Teleworker Gateway)
need to be able to initialize the PCIe wifi device. Normally, this is done
during the early stages of booting linux, because the necessary init code
is read from the memory mapped SPI and passed to pci_enable_ath9k_fixup.
However,this isn't possible for devices which have the init code for the
Atheros chip stored on NAND in an UBI volume. Hence, this module can be
used to initialze the chip when the user-space is ready to extract the
init code.
Martin Blumenstingl made a few fixes and added support for lantiq:
kernel: owl-loader: add support for OWL emulation PCI devices
kernel: owl-loader: don't re-scan the bus when ath9k_pci_fixup failed
kernel: owl-loader: use dev_* instead of pr_* logging functions
kernel: owl-loader: auto-generate the eeprom filename as fallback
kernel: owl-loader: add a debug message when swapping the eeprom data
kernel: owl-loader: add missing newlines in log messages
kernel: owl-loader: add support for the lantiq platform
These patches have been integrated. Thanks!
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
General convention is to keep U-Boot and radio calibration
data (ART) mtd partitions marked as read-only.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This changes the sysupgrade format. To support upgrades from the old
firmware to the new one, legacy images are provided. Because of the old
partition split, these have to be specific to the NOR or SPI device.
The new sysupgrade images are suitable for begin put on flash directly,
and they are independent of NOR vs SPI flash variant.
Flashing back to old firmware is supported via using the old full-flash
images instead of the old sysupgrade images.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There are currently two stock firmwares for the TL-WDR3600/4300, a US and
a universal version. Both allow installing images with US region code, so
we don't need to provide multiple images.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Simplify modifying some of the images without affecting the others.
While we're at it, also unify the profiles to use := syntax and add "v1" to
the TL-WDR4300 name to make things more consistent.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
clean up usb gadget support:
- rename gadget modules so that they appear together and are easier to
identify as gadget modules
- make usb-lib-composite and usb-gadget hidden as there is no point in
selecting those without gadget drivers that require them as deps
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The D-Link DIR-860L B1 has a flash chip which doesn't support
4K sectors. Since the DIR-860L B1 was the only mt7621 board which had
the 4k blocksize set, the 4K sector support is removed from the kernel
config.
I've checked the flash chips of all boards having set a 4K blocksize
again. This time I searched harder to finding bootlogs instead of
relying on wikis articles and/or the device tree source file.
The Planex MZK-DP150N has an en25q32b instead of the mentioned one in
the dts. Albeit the en25q32b supports 4K sectors, 4K support is not
enabled in the driver. Change the blocksize for this board back to 64K.
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Mathias Kresin <dev@kresin.me>
This is a follow up to 28110727f1
"ramips: set blocksize for 4MB devices". I've missed to include the
required changes of the kernel configs to enable 4K sector size
support.
The option is only enabled for targets having boards with 4k sector
size flash chips.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Using pad-to instead of passing the optional padding to append-kernel
or append-rootfs. It could be that the value of a variable is passed.
In case the variable is empty no error is thrown.
Furthermore the purpose of the extra parameter is hard to get without
reading the code.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Backport patches from upstream Linux kernel which are making the
kernel stores the appended dtb not in the same resisters as defined in
the UHI specification, use a separate variable on MIPS.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[some modifications]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Only add them where they are actually required.
Should help with compatibility issues with stock U-Boot images that
access UBI
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The KERNEL_SIZE variable is unset and no padding is applied. This looks
like a typo to me since the ubinized image need to be aligned to the
flash blocksize.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The kernel size isn't passed to the append-kernel build step and the
resulting image bricks the device.
Fixes FS#168.
Signed-off-by: Mathias Kresin <dev@kresin.me>
- quote the interface name
- remove call of not existing function
- remove the proto if it's the default proto
Signed-off-by: Mathias Kresin <dev@kresin.me>
No functional change, it's just to have the same style everywhere. This
way I don't need to use any regex magic to extract all subtargets for
compile tests.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add or fix the physical port number of switch ports to allow LuCI to
display the ports in physical order.
Remove the physical port number in case bridge port and physical port
order are the same.
Reorder the ucidef_add_switch parameter to be aligned with the switch
port number.
Remove board settings which are covered by the default case and remove
comments.
Signed-off-by: Mathias Kresin <dev@kresin.me>
As usual these patches were extracted and rebased from the raspberry pi repo:
https://github.com/raspberrypi/linux/tree/rpi-4.4.y
Also adds support for Raspberry Pi Compute Module 3 (untested).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
commit a2386c384d requires the
module to be static in the kernel.
So lets actually add support for it inside the kernel config.
Tested on Ventana
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Now that all seama images are using the new build code this seama recipe
used with the old build code can be dropped.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Set the blocksize for devices having only 4MB of flash for ramips
devices already using the new image build code.
Informations about the used flash chip are gathered from the OpenWrt
wiki, wikidevi, forums, OEM bootlogs or the compatible property in the
device tree source file.
The en25q32b from the AirLive Air3GII does not have 4k support in the
kernel.
For the following boards no information about the used flash chip could
be found and a 64k blocksize is assumed:
- Ralink V11ST-FE
- Ralink AP-RT3052-V22RW-2X2
- MediaTek MT7628 EVB
- MediaTek MT7621 EVB
- UPVEL UR-326N4G
- Buffalo WZR-AGL300NH
Signed-off-by: Mathias Kresin <dev@kresin.me>
Some devices (e.g. Tenda AC9 based on BCM47189B0) have BCM53125 with
port 5 connected to the second Ethernet interface on the SoC. In such
case there is no PHY and we need to force link manually.
This assumes port 5 can be marked as enabled for such devices. It's not
implemented yet unfortunately.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The insertion or removal of the sd-card cannot be detected
by the hardware itself. This is by design. To workaround this,
for the WNDR4700 unload/load the dwc2 module in case the
the special SD CARD GPIO line is low/high.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
First two patches weren't marked for stable but are dependencies for
laters ones. The rest of patches was marked for stable but most likely
will be backported to 4.5+ only so we need to get them on our own.
An important fix is eea2fb4851e9d ("ovl: proper cleanup of workdir") as
it allows mounting overlayfs with dirty workdir, e.g. after power cut.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
If the toolchain is packaged for later use as external toolchain, the resulting
tarball is created in $BIN_DIR. But without building all packages first that
directory isn't created, hence 'make target/toolchain/compile' fails when
trying to create the toolchain tarball with error "Cannot open: No such file or
directory".
To fix that the $BIN_DIR is created before using it.
Signed-off-by: Micha Lenk <micha@lenk.info>
Russell Senior reported an issue with the MR24 initramfs kernels:
> ## Booting kernel from Legacy Image at 00c10000 ...
> Image Name: POWERPC LEDE Linux-4.4.19
> Created: 2016-08-31 11:57:05 UTC
> Image Type: PowerPC Linux Kernel Image (gzip compressed)
> Data Size: 2155723 Bytes = 2.1 MiB
> Load Address: 00000000
> Entry Point: 00000000
> Verifying Checksum ... OK
>Wrong Ramdisk Image Format
>Ramdisk image is corrupt or invalid
For the MR24, the kernel is uploaded to 0x10000. The ramdisk starts
at 0x200000. This leaves the kernel with just 0x1f0000 bytes = 1984kb.
This patch adds a size check so the image creation script will abort
instead of producing a unbootable initramfs image. A separate patch
"apm821xx: Fix initramfs image for the Meraki MR24" which fixed the
reported issue was submitted earlier.
Cc: Russell Senior <russell@personaltelco.net>
Cc: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
When gzip is used, our kernel is too large and this causes the ramdisk
to be at the wrong offset. Fix by moving to lzma.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Add a patch to backport 5185c91385d73cdf79836eb8548e4726e43ae831
from Linux 4.8 adding USB2380 support to the NET2280 driver and
create an OpenWrt menu option to select it as a module.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Gateworks Ventana GW553x is a single-board computer based on the NXP
IMX6 SoC with the following features:
* IMX6 DualLite Soc (supports IMX6S,IMX6DL,IMX6Q)
* small form factor (35x70mm)
* 512MB DDR3 DRAM (2x32bit) (options up to 2GB)
* 256MB NAND flash (4GB option)
* Gateworks System Controller:
- hardware watchdog
- hardware monitor
- pushbutton controller
- EEPROM storage
- power control
* JTAG programmable
* 1x miniPCI socket (with PCIe, USB, SIM)
* 1x microSD socket
* 1x SIM socket
* Inertial Module (LSM9DS1 9DOF: 3x acc, 3x rate, 3x mag)
* analog CVBS video in
* GPS (optional uBlox EVA-M8M)
* Application headers:
- 2x TTL UART (TX/RX)
- 4x TTL GPIO (3x configurable as PWM)
- 3x CVBS Analog video input (1x decoder with 3x selectable inputs)
* Front panel connectors:
* micro-HDMI audio/video out
- 1x user programmable LED
- 1x configurable user pushbutton
- 1x USB OTG
See http://www.gateworks.com for more info
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Added gen_mvebu_sdcard_img.sh to facilitate creating an fixed-size sdcard image,
adding the bootloader and populating it with actual data.
Added the required rules for creating a 4GB sdcard image according to this layout:
p0: boot (fat32)
p1: rootfs (squashfs)
p2: rootfs_data (ext4)
This should be generic to any mvebu boards that can boot from block storage.
Added the new sdcard image to the Clearfog image profile.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup]
The u-boot variant for the clearfog is provided by the uboot-mvebu-clearfog,
and not by the generic uboot-mvebu packae.
Make sure the clearfog variant is selected when building for it.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This triggers HAS_FPU=y, and unsets CONFIG_SOFT_FLOAT.
Considering all mvebu boards have an fpu, this is the desirable behaviour.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
microSD is the primary boot media for the Clearfog Pro board, and should
work unconditionally.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup]
Add Support for the ESMT_F25L32QA and ESMT_F25L64QA.
These are 4MB and 8MB SPI NOR Chips from Elite Semiconductor Memory Technology
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
TP-Link has started providing US- and EU-specific stock firmwares that only
allow upgrading to firmwares with the same region code. Provide factory
images for both these regions.
To avoid confusing users outside these regions, we still provide a
"universal" factory.bin without a region code, although flashing either of
the US and EU images would work as well.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Historically on ARC we started from initramfs-based images because:
a) It was much easier to debug especially when toolchain and other
components were changing quite dynamically
b) It was our usual approach for embedded Linux
But now with ARC port of Lede/OpenWRT getting more stable and mature
we're ready for more real-life scenarios with FS permanently stored
on SD-card. This essentially benefits from ability to setup devices
that survive reboots with all settings and extra packages kept in place.
Still we keep an ability to build images with initramfs.
This allows us to use storage-less simulators for testing still.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: John Crispin <john@phrozen.org>
Cc: Jo-Philipp Wich <jo@mein.io>
If we want to boot from SD-card we need to have corresponding
drivers already built-in so there's no point in having these
modules.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Now when we're switching to FS on SD-card it's necessary to have
full stack of MMC block & FC drivers built-in otherwise kernel won't
be able to mount FS with needed modules.
Also we enable parsing of input parameters passed to the kernel by
U-Boot. Otherwise kernel won't know where to look for command line and
what's worse device tree blob (we had to disable this by default for
cases when kernel is loaded by JTAG and core registers may have
undefined state lading to kernel going bonkers).
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
As support of ARC 770 in OpenWRT/Lede matures we don't need
debug-only output binaries any longer, so purging vmlinux for
AXS10x boards.
As for uImage for nSIM it makes completely no sense because there's no
way to run U-Boot on nSIM.
So we remove add_arcYYY_XXX scripts making code more compact and
cleaner.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Drivers have been modified to use it and new ones have to be written
this way, so we need it for backporting code.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
With 12fe4b5798 I switched the ath5k
eeprom extraction to an alternate code path. Unfortunately this code
seams to be broken since ages and broke the ath5k EEPROM extraction.
Reported-by: Mohammed Berdai <mohammed.berdai@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: John Crispin <john@phrozen.org>
DW GMAC on ARC SDP boards doesn't enter promiscuous mode if
Ethernet PHY haven't got established link. Good examples are
auto-negotiation in progress or disconnected cable.
We do see Linux kernel sets GMAC's MAC filter register
properly but GMAC's hardware doesn't accept new settings.
We believe it is a hardware issue, most probably problem of
integration of DW GMAC and PHY on the board.
As a work-around we completely disable frame filtering
in GMAC hardware (once and for good) which forces GMAC to enter
promiscuous mode with the first write to MAC filter register.
That gives us working bridge that consists of eth0 and wlan0
(USB Wi-Fi dongle). I.e. we finally have working "Dumb AP" setup made
of ARC AXS10x boards.
Given that hack is quite dirty (in loaded wired networks this will
effectively load CPU with junk packets even if user doesn't need promisc
mode) and there's no indication any other boards with DW GMAC suffer
from the same issue we're patching only kernel for ARC boards.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: John Crispin <john@phrozen.org>,
Cc: Felix Fietkau <nbd@nbd.name>
This allows referencing USB ports/devices that are always present in a
device. This applies to some internal devices, root hub ports and
internal USB hubs.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The R7800 is an IPQ8065, so rename its dts file to reflect that fact.
Also fold the R7500v2 dts addition into the existing 800-devicetree.patch.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
1004kc is just a SMP capable 34kc, and GCC treats 24kc and 34kc exactly
the same and will generate identical code, so there is no need to tune
to 1004kc instead of 24kc.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
GCC treats 24kc and 34kc exactly the same and will generate identical
code, so there is no need to tune to 34kc instead of 24kc.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
GCC treats 24kc and 34kc exactly the same and will generate identical
code, so there is no need to tune to 34kc instead of 24kc.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked broken.
Runtime-tested on ar71xx, octeon and x86/64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Point to correct devices when booting from msata or MMC
Changes fetched from Gateworks git
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[Jo-Philipp Wich: rebased to apply against current LEDE version]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Alexis Green <alexis@cessp.it>
[Jo-Philipp Wich: add missing DEVICE_TITLE, fix model name in commit title]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
According to Jonas Gorski this is no longer needed, the problem
originally addressed by first adding 07_preinit_iface and subsequently
merging that into 02_network was probably a bug during the transition
to the new board.d pre-init approach.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Device/AVM unconditionally inherits Device/NAND, which changes the
sysupgrade image to sysupgrade-tar (instead of a "raw" sysupgrade image
as used in the Device/Default template).
This moves the Device/NAND call to the FRITZ3370 device definition, as
this is the only AVM/EVA device that uses NAND.
Additionally we have to define the IMAGE_SIZE for the AVM/EVA NOR
devices to ensure that the images are not discarded.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
The image builder does not bundle sub-directories within $(KERNEL_BUILD_DIR),
therfore the intermediate "ventana-uImage.boot" directory is not shipped,
leading to failures with "make image" later on.
To circumvent the issue, store the intermediate boot files as tar archive
instead of putting them into a directory to ensure that they end up in the
final image builder tarball. Fixes FS#102
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The image generation for TEW-691GR and TEW-692GR was broken since
79d02229 due to the move of the UMedia recipe to another Makefile.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Due to the missing phy-mode setting, the switch wasn't initialised.
The wireless requires an eeprom to work. Use the same mac addresses as
the stock firmware.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The AR8327 initvals were not copied to the DTS during the switch from
mach file to device tree and broke the switch on the device.
The former used PORT6 related initvals were wrong and have been
corrected.
The phy mode setting for the switch was missing in the DTS as well.
The wireless requires an eeprom to work. The dual band wireless chips
have both bands enabled by default but only one band per chip is
working.
The stock firmware uses the following mac addresses:
LAN: AA:BB:CC:DD:EE:E4
WAN: AA:BB:CC:DD:EE:E4
2.4GHz: AA:BB:CC:DD:EE:E4
5 GHz: AA:BB:CC:DD:EE:E8
Assuming the mac address range :E4 to :E8 is reserved for this device,
the MAC addresses were reorder to have a unique MAC address for each
interface:
LAN: AA:BB:CC:DD:EE:E4
2.4GHz: AA:BB:CC:DD:EE:E4
WAN: AA:BB:CC:DD:EE:E5
5 GHz: AA:BB:CC:DD:EE:E8
Signed-off-by: Mathias Kresin <dev@kresin.me>
Fixes the following compiler warning:
Warning (reg_format): "reg" property in /ethernet@10100000/port@0 has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /ethernet@10100000/port@0
Warning (avoid_default_addr_size): Relying on default #size-cells value for /ethernet@10100000/port@0
Signed-off-by: Mathias Kresin <dev@kresin.me>
As it turned out we may actually build both initramfs and
SD-based images in one run with just a small tweak in
existing image/Makefile and so we do here.
We're back with one "generic" target for all ARC HS38-based bords.
Kudos to John for his patience and very helpful tips!
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Jo-Philipp Wich <jo@mein.io>
Previous version was based on code from kernel 2.6.22 with Broadcom two
trivial modifications. This updates the copy to the version from current
kernel and refreshes the patch.
This was tested for regressions on Netgear R6250 (BCM4708A0), D-Link
DIR-885L (BCM4709C0) and Tenda AC9 (BCM47189B0).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
We finally got kernel booting on this device and LAN ports are working,
so it won't "brick" the device. One more big missing thing is WAN port
support. It requires fix for BCM53125 to get switch port 5 working.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Over a year ago in a commit ac96a1665a ("bcm53xx: update Disable MMU
and Dcache during decompression") we switched to Florian's patch for
workarounding CFE bug. The main difference was using a part of existing
__armv7_mmu_cache_flush instead of implementing flushing separately.
This worked well for Northstar devices but doesn't work for BCM53573 as
these devices simply don't start booting with Florian's patch. It's
because of the ldmfd ASM instruction in the __armv7_mmu_cache_flush.
So this commit switches back to using standalone implementation. This
time instead of copying Broadcom's copy of cache-v7.S, we just make a
copy of the original file on our own. Unfortunately we can't cross-dir
compile cache-v7.S from ../../mm/ as that one also adds __INITDATA with
define_cache_functions v7 which would just trigger
> Error: unrecognized/unsupported machine ID (r1 = 0x0000007f).
The only real change Broadcom did in copied .S file was modifying mcr
instruction to use c6 instead of c14. It isn't clear to me if we really
need it, but let's use it for now.
By the way we also update commit message of the
[PATCH] ARM: BCM5301X: Disable MMU and Dcache during decompression
This makes kernel booting on BCM53573 successfully.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Zbtlink ZBT-WE1526 is based on Qualcomm Atheros QCA9531 v2.
Short specification:
- 650/400/200 MHz (CPU/DDR/AHB)
- 5x 10/100 Mbps Ethernet
- 1x USB 2.0
- 128 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- two external, non-detachable antennas
- 8x LED, 1x button
- UART header (pinout: VCC, RX, TX, GND)
Flash instruction:
Use sysupgrade in vendor firmare which is based on OpenWrt.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
It was needed upstream to avoid bcma references in the main code. To
match this new code our patch adding SRAB was also updated.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Historically on ARC we started from initramfs-based images because:
a) It was much easier to debug especially when toolchain and other
components were changing quite dynamically
b) It was our usual approach for embedded Linux
But now with ARC port of Lede/OpenWRT getting more stable and mature
we're ready for more real-life scenarios with FS permanently stored
on SD-card. This essentially benefits from ability to setup devices
that survive reboots with all settings and extra packages kept in place.
Still we keep an ability to build images with initramfs.
This allows us to use storage-less simulators for testing still.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: John Crispin <john@phrozen.org>
If we want to boot from SD-card we need to have corresponding
drivers already built-in so there's no point in having these
modules.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Now when we're switching to FS on SD-card it's necessary to have
full stack of MMC block & FC drivers built-in otherwise kernel won't
be able to mount FS with needed modules.
Also we enable parsing of input parameters passed to the kernel by
U-Boot. Otherwise kernel won't know where to look for command line and
what's worse device tree blob (we had to disable this by default for
cases when kernel is loaded by JTAG and core registers may have
undefined state lading to kernel going bonkers).
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
As support of ARC HS38 in OpenWRT/Lede matures we don't need
debug-only output binaries any longer, so purging vmlinux for
AXS10x boards.
As for uImage for nSIM it makes completely no sense because there's no
way to run U-Boot on nSIM.
So we remove add_archs38_XXX scripts making code more compact and
cleaner.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Instead of using off-the-tree .dts files for ARC boards we're
switching to use in-tree ones. And for that to work properly
we apply upstream patch that adds currently missing "model"
property.
Upstream patch and discussion could be found here:
http://lists.infradead.org/pipermail/linux-snps-arc/2016-August/001394.html
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Cc: John Crispin <john@phrozen.org>
These 2 trivial patches will be followed by a bigger bgmac rework so
they are worth backporting in a separated patch.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This fixes flash corruptions. It touches bcm47xxsflash driver shared
between brcm47xx and bcm53xx so put it in generic.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It was adding unused variable:
drivers/mtd/devices/m25p80.c: In function 'm25p80_write':
drivers/mtd/devices/m25p80.c:85:6: warning: unused variable 'i' [-Wunused-variable]
int i;
^
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Use priv->wan instead of priv->id as indicator if packets should go to the
Ethernet WAN group (DPID=1) or not (DPID=0). This way, it's independant of
interface names or indexes.
Signed-off-by: Martin Schiller <mschiller@tdt.de>
By default USB LEDs are associated with usbdev trigger. However,
not all devices which have USB LEDs have kmod-ledtrig-usbdev in their
list of default packages. Add it to the relevant devices.
Signed-off-by: Matti Laakso <matti.laakso@outlook.com>
With an own DMA TX channel for each network device (eth0 + eth1) there
won't be any "tx ring full" errors any more.
This patch also move the spinlocks to the channel level instead of locking
the whole xrx200_hw structure.
Signed-off-by: Martin Schiller <mschiller@tdt.de>
The mw4530r-v1 profile in tp-link.mk is for Mercury MW4530R.
There is no such a device called TL-WDR4530.
Also change MERCURY to Mercury in /lib/ar71xx.sh
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The bootmem area reserved for crashlog might be smaller than CRASHLOG_OFFSET
bytes, leading to an integer underflow when calculating the memory address
in crashlog_set_addr() which subsequently causes the kernel to crash when
attempting to vmap() the crashlog pages.
Change the logic to only consider the offset when the size of the used memory
area is sufficient.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
It adds and uses ILP clock that requires some other work (in progress)
for upstreaming it. Other than that it adds a quick fix for bcma to add
serial flash before trying to read SPROM.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It wasn't accepted upstream as there was a discusson on Northstar vs.
BCM53573. Once we get a new ARM arch Kconfig entry it should be
possible to upstream it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Instead of introducing a fake filesystem type, move the tar generation step
directly into the image build step.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The previous image building code rework removed the rootfs.tar.gz with embedded
kernel and dtb build artifact which is required to build suitable SD images.
Reintroduce a .tar.gz artifact locally which embeds kernel and dtb, similar to
how the old code handled it.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Yue Cao claims that current host rate limiting of challenge ACKS
(RFC 5961) could leak enough information to allow a patient attacker
to hijack TCP sessions. He will soon provide details in an academic
paper.
Backports upstream commit 75ff39ccc1bd5d3c455b6822ab09e533c551f758
to the used LEDE kernel versions.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Should fix parser data containing uninitialized values for of probed
physmap flashes, which could break e.g. the redboot parser.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
This generates proper images when using CONFIG_TARGET_MULTI_PROFILE and
CONFIG_TARGET_PER_DEVICE_ROOTFS.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Thanks to this images for SoftMAC devices don't get brcmfmac anymore and
b43 is added for devices with (quite poor) support only.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
9pfs is used by kvm to share files between host and guest,
add proper config option to enable it.
Signed-off-by: Matteo Croce <matteo.croce@canonical.com>
This allows building images for selected devices with brcmfmac only
(without b43 which is for SoftMAC devices).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
Thunder Timecloud is a small NAS with MT7621A. It has 1 USB port and an
SD Card slot. There is no wireless cards.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Due to the missing carrier status set, the interface wasn't usable on a
BTHOMEHUB2B after ip link down and up as it is done in preinit.
Signed-off-by: Mathias Kresin <dev@kresin.me>
According to the author of the cpu temp driver, not all xrx200 boards
have a cpu temperature sensor. For that reason enable the sensor only
for tested boards.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Do not set the lan mac address for boards which having the lan mac
address already set in device tree source file.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The device tree binding and the associated code duplicates functionality
already patched into the etop driver. The compatible string isn't used
any more. Therefore the whole code can be dropped.
The "mac-increment" property allowed to increment a mac address received
via kernel cmdline. This functionality isn't used by any device and
should be added as etop driver device tree property if required again.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the generic mtd-mac-address dts property to get a mac address from
flash instead of the lantiq specific one.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the same mac address increment in device tree source file and
userspace.
Don't add a mac address increment to either the only mtd mac-address or
to all mac-addresses.
Fix a typo in the TDW89X0.dtsi file to add an increment.
Signed-off-by: Mathias Kresin <dev@kresin.me>
All device tree nodes are using the named properties now and the code
path handling the reg property isn't required any more.
The code related to the ath,eep-flash property has been reformatted to
be better readable.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The conversion to the new image building code accidentally caused the kernel
image to get compressed twice, leading to boot failures when kernel and rootfs
are flashed separately.
The sysupgrade images have been unaffected by this. Also restore the elf
kernel build artifact while we're at it.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
